background image

WASHER SAFETY

Save these instructions

To reduce the risk of fire, electrical shock, or injury when using your washer, adhere to the
following basic precautions.

Read all instructions before using your washer



Flammable fluids (dry cleaning solvents,
kerosene, gasoline etc.) should not be
used or stored on or near your washer.
Do not add flammable fluids to your wash
water. These substances give off
vapours that can create a fire hazard or
explosion.



The appliance is not intended for use by
young children or infirm persons without
adequate supervisions.



Young children should be supervised to
ensure they do not play with the
appliance.



After starting a washing cycle, do not
reach into the spin basket until all motion
has stopped.



Do not tamper with the controls.



If the appliance is supplied from an
extension cord set or electrical portable
outlet device, it should be positioned so it
is not subjected to splashing or ingress
moisture.



If the supply cord is damaged, it must be
replaced by the manufacturer or qualified
service agent in order to avoid any
potential hazard.

Please….



Have only a qualified person install,
repair, or replace parts on the washer.



Maintain washer properly.



Protect washer from the weather and
keep it where the temperature will not fall
below freezing.



Do no install the washer at a place of
extremely high humidity. It could cause
an electrical shock or a short circuit.



Connect washer to the correct outlet,
electrical supply, water supply, and drain
supply.



Ground washer properly.

Understanding your responsibilities



Do not use chlorine bleach and ammonia or acid (such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.



Do not wash fibreglass materials. Small particles can stick to fabrics washed in following
loads and cause skin irritation.



Do not use hot water if standard temperature is over 50C (122F). It could cause
deformation of plastic parts.



Do not spray water on the control panel and back cover of the washer. It could cause fire
or electric shock.



In case of the dual valve model, if you can connect the cold-water inlet only, while the
temperature is selected as hot or warm, there can be water leakage from the
unconnected water valve.

Summary of Contents for NWTL656


















Reviews: