background image

ISSUED: 08-05-08  SHEET #: 056-9008-6   06-28-10

Visit the Peerless Web Site at www.peerlessmounts.com

2 of 10

For customer care call 1-800-865-2112 or 708-865-8870.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Extension Columns / Ceiling Plate ...................................................................................................................4

Installation to Wood Joist Ceilings ..........................................................................................................................................5

Installation to Concrete Ceilings .............................................................................................................................................6

Installation to Threaded Rods .................................................................................................................................................7

Attaching Adapter Plate to Projector.......................................................................................................................................8

Attaching Adapter Plate to Projector Mount............................................................................................................................9

Projector Alignment ..............................................................................................................................................................10

Tools Needed for Assembly

  stud fi nder ("edge to edge" stud fi nder is recommended)

phillips screwdriver

drill

1/4" bit for concrete surface

NOTE:

 Read entire instruction sheet before you start installation and assembly. 

5/32" bit for wood studs

level

•  Do not begin to install your Peerless product until you have read and understood the instructions and warnings 

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please 
call Peerless customer care at 1-800-865-2112.

•  This product should only be installed by someone of good mechanical aptitude, has experience with basic building 

construction, and fully understands these instructions.

•  Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

•  Never exceed the Maximum UL Load Capacity. See page 1.

•  If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of 

an "edge to edge" stud fi nder is highly recommended.

•  Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

•  Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding 

power.

•  This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal 

injury.

•  This product was designed and intended to be mounted to the following supporting surfaces checked below with 

the hardware included in this product as specifi ed in the installation sheet. To mount this product to an alternative 
supporting surface, contact Peerless customer care at 1 800 865-2112.

•  This product was designed to be installed on the following ceiling construction only;

CEILING CONSTRUCTION  

ADDITIONAL HARDWARE REQUIRED

 x 

Wood 

Stud 

  None

x

 

Wood 

Joist 

  None

x

 

Solid 

Concrete 

  None

   

Cinder Block 

 

 

Contact Customer Service (Not Evaluated by UL)

   

Metal Stud 

 

 

Do not attach except with Peerless accessory kit for metal studs;

 

 

 

 

 

Contact Customer Service for Peerless accessory kit for metal studs.

 

 

    (Not 

Evaluated 

by 

UL)

   

Brick 

 

 

 

Contact Customer Service (Not Evaluated by UL)

   

Other or unsure? 

 

Contact Customer Service (Not Evaluated by UL)

WARNING

Summary of Contents for NP600CM











Reviews: