background image

3

CAUTION

• Do not obstruct the projector's ventilation

holes. Doing so will prevent the dissipation
of heat and may result in fires. In
particular, do not use the projector in the
following ways:
Do not install the projector in a wall or in a
tight place where ventilation is poor, place
a cover it, etc.

• Do not install the projector in front of the

outlets of an air conditioner or heater or in
a place where vibrations are strong. 
Doing so may result in fires.

• Do not install the projector in humid or

dusty places or exposed to smoke or
steam (such as near cooking equipment or
humidifiers). Doing so may result in fires.

• When installing the projector, leave

sufficient space between it and
surrounding objects. Failure to leave
sufficient space will prevent the dissipation
of heat and may result in fires.

• When removing the screws on left and

right on the mounting adapter, be sure to
support the projector while doing so.
Failing to do so may result in the projector
swinging back abruptly and causing injury.

• for PLUGGABLE EQUIPMENT, the

socket-outlet shall be installed near the
equipment and shall be easily accessible.

Installation Precautions

• Special techniques are required for the

installation work of the projector and

installation work should only  be

undertaken by qualified and licenced

installers.

• NEC Display Solutions will not accept any

responsibility related to any accidents or

incidents due to insufficient or inferior

mounting techniques.

Installation Location

Avoid places of high temperature or low

temperature. 

(For ambient operating temperature, see the

user's manual included with the projector.)

Avoid places exposed to direct sunlight and

the vicinity of ventilation holes of room air

conditioning and heating.

Avoid rooms with a lot of dust, humidity,

greasy smoke, or tobacco smoke.

Dirt will adhere to optical parts such as

lenses and mirrors and this will cause a

deterioration of image quality.

Avoid places in which the screen is exposed

to direct sunlight or illumination light.

When surrounding light directly hits the

screen, the image appears washed out and

is difficult to view.

Heed the Following

NP06CM-E  07.3.20 9:02 AM  ページ 3

Summary of Contents for NP06CM

















Reviews: