background image

 

ちゅう 

本書は製品とともに大切に保管してください 

Please keep this guide carefully with the product.

 

 

 

N8190-154 

Fibre Channel コントローラ(2ch) 

ユーザーズガイド 

Fibre Channel Controller (2ch) 

User's Guide

 

 
 

まえがき 

  このたびは、N8190-154 Fibre Channel コントローラ(2ch)をお買い上げいただきまことにありがとうございます。 
 
  本書は、N8190-154  Fibre  Channel コントローラ(2ch)(以下「本製品」と呼びます)を正しく、安全に設置、使用する
ための手引きです。本製品を取り扱う前に必ずお読みください。また、本製品を使用する上でわからないこと、不具
合が起きたときにもぜひご利用ください。本書は、必要な時にすぐに参照できるように必ずお手元に保管してくださ
い。 
 
 
  本製品を取り付ける基本処理装置(以下「本体装置」と呼びます)の取り扱いについての説明は、本体装置に添
付されたユーザーズガイドを参照してください。また、本製品を取り扱う前に「使用上のご注意」、「取り扱い上のご
注意」を必ずお読みください。 

 

Preface 

 
Thank you very much for purchasing the N8190-154 Fibre Channel Controller (2ch). 
 
This is a guide to the safe and proper use of the N8190-154 Fibre Channel Controller (2ch) (hereafter, this 
product).    Be sure to read this guide before handling this product.    Please refer to this document if there is 
something that you do not understand or a problem occurs while using this product.    Store this guide close 
to this product for easy reference.   
 
 
For an explanation on the handling of the basic processing unit (hereafter, Computer) that this product is 
installed in, please refer to the User's Guide that came with the basic processing unit.    In addition, be sure 
to read the sections entitled "Safety Precautions" and "Precautions on Use" before handling this product.   
 

Summary of Contents for N8190-154

















































Reviews: