manualshive.com logo in svg

NEC MultiSync EA271F, User Manual

Share
Download
NEC MultiSync EA271F User Manual Download Page 23

English-21

English

Specifications

Monitor Specifications

MultiSync EA271F

Notes

LCD Module 

Diagonal: 

 

Viewable Image Size: 

 

Native Resolution (Pixel Count): 

68.60 cm/27 inches 
68.60 cm/27 inches 
1920 x 1080

Active matrix; thin film transistor (TFT) liquid crystal 
display (LCD); 0.311 mm dot pitch; 250 cd/m

2

 white 

luminance; 1000:1 contrast ratio (typical), (5000:1 
Contrast ratio, Dynamic).

Input Signal

DisplayPort: 

DisplayPort Connector:

Digital RGB

DisplayPort V1.1a (HDCP1.3)

DVI: 

DVI-D 24pin:

Digital RGB

DVI (HDCP1.4)

VGA: 

Mini D-Sub 15-pin:

Analog RGB 
Sync

0.7 Vp-p/75 ohm 
Separate sync.TTL level Positive/Negative 
Composite sync.TTL level Positive/Negative 
Sync on Green  
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)

HDMI: 

HDMI Connector:

Digital YUV 
Digital RGB

HDMI (HDCP1.4)

Display Colors

16,777,216

Synchronization Range  

Horizontal: 

  

Vertical:

31.5 kHz to 83.0 kHz
50 Hz to 75 Hz

Automatically 
Automatically

Viewing Angle 

Left/Right: 

 

Up/Down:

±89° (CR > 10)

 

±89° (CR > 10)

Image Formation Time

6 ms (Gray to gray Typ.)

Active Display Area 

Landscape: Horiz.: 

 

Vert.: 

  

Portrait: Horiz.: 

 

Vert.:

597.89 mm/23.5 inches
336.31 mm/13.2 inches
336.31 mm/13.2 inches
597.89 mm/23.5 inches

USB Hub 

I/F: 

 

Port: 

 
  

Load Current:

USB Specification Revision USB 3.1 Gen 1
Upstream 1 
Downstream 3 
Maximum 0.9 A per port for USB 3.1 Gen 1

Upstream port applicable to USB monitor control.

AUDIO

Audio Input: 

STEREO Mini Jack: 

 

DisplayPort Connector: 

 

HDMI Connector:

Analog Audio 
Digital Audio 
Digital Audio

Stereo L/R 500mV rms 20 Kohm 
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit) 
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)

Headphone Output:  STEREO Mini Jack:

 

Headphone Impedance 32 Ohm

Speakers 

Practical Audio Output:  1.0 W + 1.0 W

ControlSync  

IN: 

(available up to 5 sub monitors) 

OUT:

Stereo Micro jack 2.5 

φ

Stereo Micro jack 2.5 

φ

Power Supply

AC 100-240 V ~ 50/60 Hz

Current Rating

0.85 - 0.45 A

Dimensions  

Landscape: 

 
  

Portrait:

610.2 mm (W) x 377.3 - 527.3 mm (H) x 250.0 mm (D)
24.0 inches (W) x 14.9 - 20.8 inches (H) x 9.8 inches (D)
359.8 mm (W) x 628.4 - 652.6 mm (H) x 250.0 mm (D)
14.2 inches (W) x 24.7 - 25.7 inches (H) x 9.8 inches (D)

Stand adjustable range   Height Adjustment:
 

 

 

Tilt / Pivot / Swivel:

150 mm/5.9 inches (Landscape orientation) 
24.2 mm/1.0 inches (Portrait orientation)
Up

 35° Down 5° / ± 90° / 340°

Weight

7.6 kg (16.8 lbs)/Without stand: 5.0 kg (11.0 lbs)

Environmental Considerations 
 

Operating Temperature: 

  

Humidity: 

 

Altitude: 

 

Storage Temperature: 

 

Humidity: 

 

Altitude:

 

5°C to 35°C/41°F to 95°F

 

20% to 80% 
0 to 16,404 Feet/0 to 5,000 m 

-10°C to 60°C/14°F to 140°F

 

10% to 85% 
0 to 40,000 Feet/0 to 12,192 m

NOTE: 

Technical specifications are subject to change without notice.

Summary of Contents for MultiSync EA271F































Reviews:

No comments

Brands by name

Popular brands

Load more brands