background image

English-6

Quick Start

To pull the stand, follow these instructions:

1. Place monitor face down on a non-abrasive surface (

Figure 1

).

NOTE:

Handle with care when monitor facing down, for avoiding damage to the front control
buttons.

2. Pull the stand holding the monitor with the other hand until the stand clicks (

Figure 2

).

NOTE:

Handle with care when pulling the stand.

NOTE:

Reverse this procedure if you need to re-pack the monitor.

To attach the MultiSync LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2.

For the PC or MAC with DVI digital output:

 Connect the DVI signal cable to the

connector of the display card in your system (

Figure A.1

). Tighten all screws.

For the PC with Analog output:

 Connect the 15-pin mini D-SUB signal cable to the

connector of the display card in your system (

Figure A.2

). Tighten all screws.

For the MAC:

 Connect the Macintosh cable adapter to the computer, then attach the

15-pin mini D-SUB signal cable to the Macintosh cable adapter (

Figure A.3

).

Tighten all screws.

NOTE:

Some Macintosh systems do not require a Macintosh cable adapter.

3. Connect all cables to the appropriate connector on the back of the monitor (

Figure B.1

). Connect Headphones

(not included) to the appropriate connector at the rear side of the monitor, if desired (

Figure B.1

).

4. Connect one end of the power cord to the monitor and the other end to the power outlet. Position the Video Signal Cable,

Audio cable and power cord between the holes on the Stand.

5. To attach the Cable management cover, insert the tabs of the Cable management cover into the holes on the Stand and

slide the Cable management cover downward into place (

Figure B.2

) making sure that the tabs are completely secure.

NOTE:

Adjust the position of the cables that are placed under the Cable management cover to avoid damaging the cable
or monitor.

NOTE:

Please refer to the Caution section of this manual for proper selection of power cord.

Cable

management

cover

Power Cable

Input (D-SUB)

Input (DVI)

Figure A.1

Figure A.3

Macintosh
Cable Adapter
(not included)

Figure A.2

DVI signal cable

Figure B.1

Figure B.2

Figure 2

Figure 1

Control buttons

Summary of Contents for MultiSync E221W



















Reviews: