background image

English-2

Canadian Department of Communications Compliance Statement

DOC: 

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL:

 Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

1.

Use the attached specified cables with the MultiSync E221W (L227HR) color monitor so as not to interfere with radio
and television reception.

(1)

The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,
and meet the following condition.

Power supply cord

Non shield type, 3-conductor

Plug shape

U.S.A

(2)

Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable.
Use of other cables and adapters may cause interference with radio and television reception.

2.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

U.S. Responsible Party:

NEC Display Solutions of America, Inc.

Address:

500 Park Blvd, Suite 1100
Itasca, Illinois 60143

Tel. No.:

(630) 467-3000

Type of Product:

Display Monitor

Equipment Classification:

Class B Peripheral

Models:

MultiSync E221W (L227HR)

We hereby declare that the equipment specified above conforms

to the technical standards as specified in the FCC Rules.

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.

E

NERGY

 S

TAR

 is a U.S. registered trademark.

ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,
Norway, Spain, Sweden, U.K.
NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.
MultiSync is a registered trademark of NEC Display Solutions, Ltd. in the countries of U.K., Italy, Austria, Netherlands,
Switzerland, Sweden, Spain, Denmark, Germany, Norway and Finland.
All other brands and product names are trademarks or registered trademarks of their respective owners.
As an 

E

NERGY

 S

TAR

®

 Partner, NEC Display Solutions of America, Inc. has determined that this product meets the 

E

NERGY

 S

TAR

guidelines for energy efficiency. The 

E

NERGY

 S

TAR

 emblem does not represent EPA endorsement of any product or service.

Summary of Contents for MultiSync E221W



















Reviews: