background image

• Do not insert objects of any kind into the audio base slots, as they may

touch dangerous voltage points, which can be harmful or fatal or may
cause electric shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord

may cause shock or fire.

• Keep the audio base away from high capacity transformers, electric

motors and other devices such as external speakers or fans, which may
create strong magnetic fields.

• To separate the equipment from the power source you have to remove

the plug from the inlet socket.

• When operating the audio base with its AC 220-240V worldwide power

supply, use a power supply cord that matches the power supply voltage
of the AC power outlet being used. The power supply cord you use
must have been approved by and comply with the safety standards of
your country. (Type H05VV-F should be used except in UK)

NOTE:

The audio base is to be used only with NEC MultiSync
monitors.

• In UK, use a BS-approved power cord with molded plug and a black

(5A) fuse installed for use with this audio base. If a power cord is not
supplied with this audio base, please contact your supplier.

Immediately unplug your audio base from the wall outlet and refer
servicing to qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the audio base.

• If the audio base has been exposed to rain or water.

• If the audio base has been dropped or the cabinet damaged.

• If the audio base does not operate normally by following operating

instructions.

• Allow adequate ventilation around the audio base so

that heat can properly dissipate. Do not block ventilated
openings or place the audio base near a radiator or
other heat sources.

• The power cable connector is the primary means of

detaching the system from the power supply. The audio
base should be installed close to a power outlet which is
easily accessible.

• Handle with care when transporting. Save packaging

for transporting.

CAUTION

E - 5

0

5

25

75

95

100

Summary of Contents for Monitor









Reviews: