background image

English-2

For the Customer to use in U.S.A. or Canada

Canadian Department of Communications Compliance Statement

DOC: 

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.

C-UL:

 Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1.

Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950-1.

FCC Information

1.

Use the attached specified cables with the AccuSync LCD19WMGX colour monitor so as not to interfere with radio and
television reception.

(1)

The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,
and meet the following condition.

Power supply cord

Non shield type, 3-conductor

Length

1.8 m

Plug shape

U.S.A

(2)

Please use the supplied shielded video signal cable and audio cable. Use of other cables and adapters may
cause interference with radio and television reception.

2.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

U.S. Responsible Party:

NEC Display Solutions of America, Inc.

Address:

500 Park Blvd, Suite 1100
Itasca, Illinois 60143

Tel. No.:

(630) 467-3000

Type of Product:

Display Monitor

Equipment Classification:

Class B Peripheral

Model:

AccuSync LCD19WMGX (TFT19Q80PS)

We hereby declare that the equipment specified above conforms

to the technical standards as specified in the FCC Rules.

Summary of Contents for LCD19WMGX - AccuSync - 19" LCD Monitor
















Reviews: