NEC Expres5800/A2040b Installation Manual Download

Page: 24 / 25

- 24 -

August

2016

855-911221-105-A

Appendix

8.1. List of LAN driver setting default value



List of default value (v15.6.0.10/16.2.0.4)

* In "Handoff of setting value", "-" means the value does not change after the update or recovery.

For the others, the values are set based on the above table after the update or recovery.

* For the properties with hatching, the corresponding values are set depending on your environment.

For the other properties, it is recommended to set to the default value.

* Regarding "Ethernet@WireSpeed", there are some cases that the confirmed value in [3.4 Save the

setting of LAN driver] is blank.
In that case, the value becomes "Enable".

* For the property with "Copper Only", there are some cases that the property is not existed depending

on the adapter or driver version but there is no problem on it.

* Regarding "Network Address", if the confirmed value in [3.4 Save the setting of LAN driver] is blank,

the value becomes "None".

Property

Default value

Handoff of setting value

After update

After recovery

802.3az EEE (Copper Only)

Disable

ARP Offload

Enabled

EEE Control Policies (Copper Only)

Optimal Power and
Performance

Ethernet@WireSpeed (Copper
Only)

Enable

Flow Control

Rx & Tx Enabled

Rx & Tx

Enabled

Interrupt Moderation

Enabled

Jumbo Mtu

1500

Large Send Offload V2 (IPv4)

Enabled

Large Send Offload V2 (IPv6)

Enabled

Maximum Number of RSS Queues

RSS 1 Queue

Network Address

None

NS Offload

Enabled

Priority & VLAN

Priority & VLAN Enabled

Receive Buffers

Default

Receive Side Scaling

Enabled

Speed & Duplex (Copper Only)

Auto Negotiation

TCP/UDP Checksum Offload (IPv4) Rx & Tx Enabled

TCP/UDP Checksum Offload (IPv6) Rx & Tx Enabled

Transmit Buffers

500

Virtual Machine Queues

WS2012 : Disabled
WS2012R2 : Enabled

Disabled

VLAN ID

VMQ VLAN Filtering

Disable

Wake On Magic Packet

Enabled

Wake On Pattern Match

Enabled

WOL Speed (Copper Only)

Lowest Speed Advertised

Lowest Speed

Advertised

Summary of Contents for Expres5800/A2040b


























Search results

Summary of Contents for Expres5800/A2040b

Reviews:

Related manuals for Expres5800/A2040b

Brands by name

Popular brands

NEC Expres5800/A2040b, Installation Manual

Search results

Summary of Contents for Expres5800/A2040b

Reviews:

Related manuals for Expres5800/A2040b

Brands by name

Popular brands