background image

3

HEED THE FOLLOWING

Read the operating instructions carefully before using the unit and be
sure to use it properly. After reading the instructions, store them in an
easily accessible place so they can be consulted whenever necessary.

WARNING

• Continued use should there be an irregularity (smoke, abnormal

smell or sound, etc.) will lead to fires or electric shocks. If there
should be an irregularity, immediately turn off the power of the
computer on which the unit is installed and request servicing.

• Do not disassemble or modify the unit in any way. Doing so will

lead to fires or electric shocks.

• Make sure that no foreign objects get in the unit, as this will lead

to fires or electric shocks. If a foreign object should get in the
unit, immediately turn off the power of the computer on which
the unit is installed and request servicing.

• Do not let fluids get in the unit or let the unit get wet, as this will

lead to fires or electric shocks. If fluid should get in the unit,
immediately turn off the power of the computer on which the unit
is installed and request servicing.

• Do not use with any power voltage other than the indicated

voltage. Doing so will lead to fires or electric shocks.

• Do not store or use the unit in places where it may be subject to

shocks or strong vibrations. Doing so will lead to fires or electric
shocks.

• Do not store or use the unit in places where it may be exposed

to chemicals or chemical vapors. Doing so will lead to fires or
electric shocks.

ECDR3001.PM5

99.1.13, 2:36 PM

4

Summary of Contents for CDR-3001

















Reviews: