background image

English-12

Specifications

Monitor Specifications

AccuSync AS193i Monitor

Notes

LCD Module

Diagonal: 48.0 cm/19 inches

Active matrix, thin film transistor (TFT) 
liquid crystal display (LCD); 0.2928 mm 
dot pitch; 250 cd/m

2

 white luminance, 

1000:1 contrast ratio, typical.

Viewable Image Size: 48.0 cm/19 inches

Native Resolution (Pixel Count): 1280 x 1024

Input Signal

15pin Mini D-sub: Analog RGB

0.7 Vp-p/75 ohms

Sync

Separate sync. TTL level (Positive/Negative)

DVI-D Digital RGB

DVI(HDCP)

Display Colors

16,777,216

Depends on display card used.

Viewing Angle

Left/Right: -89°/+89° (CR>10)

Up/Down: -89°/+89° (CR>10)

Synchronization Range

Horizontal: 31.5 kHz to 81.1 kHz

Automatically

Vertical: 56 Hz to 76 Hz

Automatically

Resolutions Supported

Landscape:

720 x 400*

1

: VGA text 

 

640 x 480*

1

 at 60 Hz to 75 Hz 

 

800 x 600*

1

 at 56 Hz to 75 Hz 

 

832 x 624*

1

 at 75 Hz 

 

1024 x 768*

1

 at 60 Hz to 75 Hz 

 

1152 x 864*

1

 at 75 Hz 

 

1152 x 870*

1

 at 75 Hz

Some systems may not support all modes 
listed.

1280 x 960*

1

 at 60 Hz to 75 Hz

1280 x 1024 at 60 Hz to 75 Hz.................

Recommended resolution is 60 Hz for 
optimal display performance.

Active Display Area

Horizontal: 374.8 mm

Vertical: 299.8 mm

Power Supply

100 - 240 V ~ 50/60 Hz

Current Rating

0.45 - 0.25 A

Power

Maximun Operation: 18 W

Consumption

Normal Operation: 14 W

Dimensions

Landscape: 408.0 mm (W) x 386.4 mm (H) x 213.9 mm (D) 

 16.1 inches (W) x 15.2 inches (H) x 8.4 inches (D)

Weight

3.9 kg (8.6 lbs)

Environmental Considerations

Operating Temperature: 

Humidity: 

Altitude: 

Storage Temperature: 

Humidity: 

Altitude:

5°C to 35°C/41°F to 95°F 
20% to 80% 
0 to 2,000 m/0 to 6,562 Feet 
-10°C to 60°C/14°F to 140°F 
10% to 85% 
0 to 12,192 m/0 to 40,000 Feet

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal 
and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen 
is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done. 

NOTE: 

Technical specifications are subject to change without notice.

Summary of Contents for AccuSync AS172-BK


















Reviews: