manualshive.com logo in svg

Neat WALL Family, User Manual

Share
Download
Neat WALL Family User Manual Download Page 7

7

WALL Family User manual NE41 12005-02 v2.0

Both ports have a common ground 

and must be connected to potential 

free contacts (see below)

.

Port 1

Port 1

Port 2

If an inserted tele plug is removed, 

the unit sends a 

Tamper alarm

. If the 

plug is inserted again the unit sends 

a 

Tamper OK alarm

.

Manual configuration

(not valid for ROOM and ROOM+PEAR)

Any unit can be manually configured 

regarding adding transmitters and 

how the two relay outputs should 

act when the added transitter is 

activated

.

The procedure is in short

:

• Determine what position to activate
• Add the radio transmitter
• Determine the action when the 

added transmitter is activated

Please read the following instruction 

carefully before attempting to 

manually configure a radio  

transmitter.

1.  Power off the unit (both 24VDC 

and batteries must be removed)

2.  Remove J2
3.  Power on the unit and replace 

the J2 within 5 seconds from 

power on

.

4.  The LED blinks green 3 times

.

Summary of Contents for WALL Family













Reviews:

No comments

Brands by name

Popular brands

Load more brands