NDT DC-3000C Series Instruction Manual Download Page 5 | Manualshive

Page: 5 / 21

background image

DC-3000C SERIES ULTRASONIC THICKNESS GAUGE

- 3 -

5. Keypad Functions

Key

Function

- On/ Off Key
- Esc. Menu

Press this key to switch on or off .
Press this Key to Escape the Menu.

- Menu Key
- Confirm Key

Press This Key to enter the Menu.
Press this Key to confirm the selection.

- Return Key
- Storage Key

Press this key to previous menu (DC-3000C)
Press this key to store current data(DC-3020C)

-Contrast
-Adjustment

Press this key to enter menu of Contrast and make
adjustment

- Up arrow Key

Achieve switch among the menu options in the
menu operation

-Down arrow Key

- Calibration Key

Achieve switch among the menu options in the
menu operation.
Put the probe in the air, press this key to complete
the manual calibration. (Under the measurement)

«
...
3
4
5
6
7
...
»

Summary of Contents for DC-3000C Series






















Reviews:

No comments

Related manuals for DC-3000C Series

Brand: QALCOMET Pages: 52

Brand: Yamaha Pages: 14

Disklavier Mark II XG Series

Brand: Yamaha Pages: 12

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 3

Brand: PASCO Pages: 2

Analite NEP-5000

Brand: Observator Instruments Pages: 103

Brand: Quadelectra Audioworx Pages: 12

WATERPROOF PHTESTR 1 PH TESTER

Brand: EUTECH INSTRUMENTS Pages: 3

AirScout Gigacheck

Brand: Greenlee Pages: 19

Brand: Keysight Technologies Pages: 45

Lange ORBISPHERE 3100

Brand: Hach Pages: 47

THERMASGARD RGTM1 Series

Brand: S+S Regeltechnik Pages: 16

Brand: Grundig Pages: 24

Heinrichs Coriolis Mass Flow Meter

Brand: Kobold Pages: 118

Brand: Welch Allyn Pages: 32

Baker DX Series

Brand: Megger Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands