manualshive.com logo in svg

NDS 90T0007, User Manual, Page: 27 / 66

Share
Download
NDS 90T0007 User Manual Download Page 27

20 

Horizontal Position   

Moves the image to the left or right. Touch 

fi

 or 

fl

 to horizontally center  the image.  

Note: 

This parameter 

is not available for SDI inputs. 
 

Vertical Position   

Moves the image up or down.  Touch 

fi

 or 

fl

 to vertically center the image.  

Note: 

This parameter is not 

available for SDI inputs.  
 

Sharpness

  

 

Touch 

fi

 or 

fl

 to adjust the sharpness (focus) of the displayed image.  

 

Overscan 

0 

= The image is displayed at a size that fills the screen without losing any video information. The image 

presented to the display may include black bars top and bottom or left and right.       

1, 2, 3, 4, 5 

or

 6 

= The image is linearly enlarged, while remaining centered, in incremental steps. As the 

image becomes larger video information will be lost from the top and bottom and / or left and right.  
Select using 

fi

 or 

fl

 buttons. 

Display Setup

 

SDI  Picture Menu 

Composite Picture Menu 

S-Video Picture Menu 

Summary of Contents for 90T0007



































































Reviews:

No comments