background image

DDPHCL2_man_r1.0 – 03/2021 

Page 2 

 

WARNINGS 

 

This  manual  is  dedicated  to  the  technical  personnel  responsible  of  the  installation, 
management and maintenance of the plants. The manufacturer assumes no responsibility for 
damages  or  malfunctions  occurring  after  intervention  by  non-authorized  personnel,  or  not 
compliant with the prescribed instructions. 

 
Before  performing  any maintenance  or  repair  action,  ensure  that the  system  is  electrically 
and hydraulically insulated. 
 

Dispose of waste material and consumables accordingly with local regulations. 

 

 

 
 
GENERAL SAFETY TIPS 

 
WARNING!

 Before performing any operation on the pump, unplug the pump and discharge 

the liquid from the pump head and tubes.

 Never operate on working pump! 

 
During  maintenance  and  repair  of  parts  that  normally  become  in  contact  with  chemicals, 

always wear all prescribed personal protections (gloves, clothes, glasses, etc.). 
The pump has to be handled by qualified personnel only. Always use original spare parts for 
maintenance. 

 

Failure  to  follow  instructions  can  cause  damage  to  the  equipment  and,  in  extreme  cases,  to 
people. 

 

 

 
How to ship the instrument 

To send back the device for repairing or calibration purposes, proceed as follows: 

  Fill the module “REPAIR REQUEST AND DECONTAMINATION DECLARATION” supplied with this 

manual, and include it in the transport documentation. 

  Clean the device properly, to eliminate any hazardous residuals. 

 

 

 

The manufacturer can modify the instrument or the technical manual without advanced notice. 

 

 

Warranty 

All our products are warranted for a period of 12 months from the delivery date.  
Warranty is not valid if all instructions of installation, maintenance and use, are not strictly followed by the user.  
Local regulations and applicable standards have also to be followed. 
In particular, the warranties regarding the operational safety and reliability of dosing pumps will be recognized 
only if the following conditions are fulfilled: 

o

  The installation, wiring, adjustment, maintenance and repairs performed only by qualified personnel 

o

  Only original spare parts have been used for repairs 

 

 

 

Summary of Contents for DDPHCL2




















Reviews: