20
WORKING WITH A DRIVE
To start the drive, pull it to the handle
1 (Fig. 8)
drive lever
2 (Fig. 8
).
You can turn off the drive at any time by releasing the drive lever and operate the device like a mower without a drive.
MOWING HEIGHT SETTING
Attention! Before changing the cutting height, stop the engine and disconnect the spark plug cable.
To set the desired cutting height, change the position of the adjustment lever
24 (Fig. 9)
located on the housing of
the mower. You can choose from 6 different cutting heights in the range of 25 - 75 mm.
INSTALLING THE GRASS BASKET
1.
Raise the mower basket cover
23 (Fig. 10).
2.
Insert the basket
7 (Fig.10)
attaching the hooks at the inlet to the basket on a rod designed for this purpose
28 (Fig. 10)
at the mower outlet cover, then lower the cover.
3.
Make sure the hooks are attached correctly.
Warning!
Often check the technical condition of the grass basket. If any parts are worn or damaged, they must be
replaced with new parts that are available at authorized service centers.
EMPTYING THE GRASS BASKET
Warning!
Stop the engine before emptying and removing the basket.
Basket full indicator
21 (Fig. 11)
allows you to quickly assess the level of basket filling. If the indicator plate is
raised while the mower is running, it means that the basket is not full yet. If the indicator plate is in a horizontal position
during the mower's operation, it means that the basket is full and should be emptied.
SETTING THE FRONT WHEELS
Due to the special design of the front wheels, the mower is extremely manoeuvrable. Wheel alignment is set when the
clamping device snaps into place
19 (Fig.12
). If we want to change the wheel position:
1.
lift the bracket to release it,
2.
put the wheel in a new position,
3.
snap the mounting brackets back into place.
In order for the front wheels to move freely, the clamping brackets must be raised
19 (Fig. 12)
and do not put them in the
hole, but place them on the plate next to it
(Fig. 12 point A)
.
CLEANING THE CUTTING UNIT CABINET
Warning!
When the engine is running, the cutting blades rotate.
1.
After finishing work, thoroughly clean the entire device.
2.
Stop the engine and disconnect the spark plug wire before cleaning the housing.
3.
Empty the fuel tank before cleaning.
4.
Without tilting the mower to the side, lay it on the ground so that the front wheels are in the air.
5.
Clean the underside of the mower with a brush and water.
Do not use high-pressure cleaning devices, as high-pressure water can break the paint protection of the housing. Do not use
intensive cleaning and washing agents, e.g. aggressive detergents, they can damage plastics and metals, which may result
in deterioration of the device's safety.
The second way to clean the housing is to use the housing cleaning system.
After connecting the hose to a special quick coupler that is already mounted in the mower housing and unscrew the water,
start the mower. The device is cleaned during the rotation of the knife, on which a strong stream rinses out flushing residues
of grass.
(Fig. 13)
MOUNTING THE SIDE DISCHARGE CHUTE
To mount the side discharge chute:
1.
open the side ejector cover
2 (Fig. 15)
(To unlock the cover, first turn the axle cover
1 (Fig. 15)
),
2.
push in the side discharge chute
3 (Fig. 15).
Summary of Contents for 3000S
