background image

 

 

1.4 Basic technical characteristics 

 

Tab 1 

 

 

S-2420 

GSM/GPRS/Bluetooth 

GSM frequency bands  

GSM 850, EGSM 900, DCS 1800, PCS 

1900 

GPRS class 

B, multislot class 12 

Transmitter power 

Class 4 (2W) в GSM 850 и EGSM 900; 

Class 1 (1W) в DCS 1800 и PCS 1900 

Maximum speed of data transfer/reception, kbit/s 

85,6 

SIM card holder 1 

external with the plug, miniSIM 

SIM card holder 2 

no 

GSM-signal jammer detector 

yes 

Bluetooth 

yes, v 4.0 

GNSS 

Supported navigation systems 

GLONASS/GPS/Galileo/QZSS 

Number of channels 

tracking: 33, Figureking-up: 99 

Sensitivity (in laboratory conditions) 

tracking: -167 dBm 

cold start: -149 dBm 

Time of first coordinates determination (for GPS and GLONASS systems with 

a signal of -130 dBm) 

cold start: 29 sec 

warm start: 22 sec 

hot start: <1 sec 

Coordinates error, (50% CEP, 24 hours in static mode, with 
signal levels -130 dBm), m 

2.5 (in plan), 5 (in height) 

Coordinate update rate, Hz 

GNSS jammer detector 

yes 

Power supply 

Operation supply voltage, V

1

 

9,5…47 

Current consumption at 12 V voltage in operation mode on 

Average

2

, mA 

80 

Current consumption at 12 V voltage with turned off 

GLONASS and GSM modules is no more than, mA 

20 

Maximum  current  consumption  at  12  V  voltage  in  the  operation  with  the 

charge of the battery is not more than, mA 

200 

Protection against polarity reversal  

yes 

Protection against prolonged overvoltage up to 500 V 

yes 

Battery

3

 

no 

Battery protection from recharge, full discharge, short circuit

4

 

no 

Quartz crystal unit 

no 

Backup battery of the navigation module 

yes 

Time of keeping of the RTC clock rate and ephemeris in a navigation module 
(with the power off and discharging of the battery) is at least, days 

Battery charging from USB 

no 

Interfaces/sensors 

Inputs against power surges, V   

up to 200 

Total number of universal (analog, discrete, pulse-frequency) inputs 

Built-in pull-up resistor for discrete or pulse-frequency inputs 

no 

Measuring range by inputs, set up as analog, V 

0…31 

Working range with frequency fuel level sensors, Hz 

1 - 3000 

USB interface for settings, control, data transfer and diagnostics 

yes 

RS-485 digital interface 

no 

RS-232 digital interface 

no 

Summary of Contents for SMART S-2420






















Reviews: