NAVIS NAVIOR-24S Page 195 Reference Manual Download

Page: 195 / 228

NAVIOR-24S

™

Appendix D

NMEA 0183 Communication Interface

195

NAVIOR-24S ™

Revision

V1.00 20.05.2008

ALVER - HW / FW version reply

This message contains basic information about the Receiver: manufacturer and the installed
hardware / firmware version.
Format:

$ALVER, mmmm, hhhhhhhh, ffff <CR><LF>

Field

Format

Details

mmmm

4 ASCII characters

Manufactures code

hhhhhhhh

8 ASCII characters

Hardware version info

ffff

4 decimal digits

Firmware version number

2 ASCII control characters

Important:

Question/Answer: once requested, one answer only, no repetition of reply.
All unused digits are filled with “0” and all unused characters are padded with “ “.
This message is only send as reply on the special request message $ARVER.

Summary of Contents for NAVIOR-24S





































































































































































































































Search results

Summary of Contents for NAVIOR-24S

Reviews:

Related manuals for NAVIOR-24S

Brands by name

Popular brands

NAVIS NAVIOR-24S, Reference Manual

Search results

Summary of Contents for NAVIOR-24S

Reviews:

Related manuals for NAVIOR-24S

Brands by name

Popular brands