Navico Simrad I3005 Page 39 Operator'S Manual Download | Manualshive

Page: 39 / 52

background image

Restore global settings

This option clears the global NMEA 2000 source selection on all
networked devices, and resets all local settings to factory default.
After a global reset you need to configure all NMEA 2000 and local
sources again when the unit restarts.

Restore local settings

Resets all local settings to factory default.
After a local reset you need to configure local sources again when
the unit restarts.

Backup and restore of system data

The system includes a backup and restore function, making it
possible to back-up and restore user settings.

Ú

Note:

It is strongly recommended to make a backup when the

system is installed and configured.

Maintenance

| I3005/I3007 Operator Manual

39

«
...
37
38
39
40
41
...
»

Summary of Contents for Simrad I3005





















































Reviews:

No comments

Related manuals for Simrad I3005

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: Ecco Pages: 3

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brand: Task Force Tips Pages: 16

Brand: JBM Pages: 13

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

Brand: Ultratune Pages: 12

Brand: EzCAP Pages: 15

Brand: Strapack Pages: 16

Brand: Hameg Pages: 60

Brand: Biosonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands