manualshive.com logo in svg

Nav TV W205v2, Install Manual, Page: 3 / 10

Share
Download
Nav TV W205v2 Install Manual Download Page 3

BHM 

10/18/18 

NTV-DOC328 

 

 

 

Agreement

: 

End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.  

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger 

entertainment only.  

3 | 

P a g e

 

 

 

Dash Removal (’15 C

-Class) 

 

1.

 

Use a plastic tool to remove the silver trim behind the COMAND 
touchpad controller. You will have to open the center console and 
press the arm rest locks forwards for clearance: 

 

 

 

 

 

 
 

2.

 

Remove (2x) Torx 20 screws hidden beneath 
the silver trim piece in step 1:  

 

 

 

3.

 

Lift up the entire dash panel to just beneath the 
screen and disconnect all (6) plugs. Set the dash panel aside in a safe 
place. 

4.

 

Unscrew (2x) Torx 20 screws securing the radio to the sub dash. These 
screws are not designed to be removed from the radio clamps.  
 
 
 
 
 
 
 
 

5.   Remove the radio 

by pulling it towards 

you.  

Summary of Contents for W205v2











Reviews:

No comments