NAUTIKA BREVA 110 CFM Installation Manual Download Page 7

BATHROOM  FAN  –  BREVA  50 / 70 / 90 / 110  CFM

1

INSTALLATION GUIDE
BATHROOM FAN

BREVA  50 / 70 / 90 / 110  CFM  MODELS

Table of contents

Introduction  ....................................................................................  1
General safety information and warnings  ........................................  2
List of parts and accessories supplied  .............................................  2
Dimensions, specifications, wiring diagram  .....................................  3

Installation steps  ........................................................................ 4 - 5
Maintenance  ...................................................................................  6
Troubleshooting guide  .....................................................................  6
Limited warranty  .............................................................................  6

INTRODUCTION
You must read and save these instructions

Please read these instructions carefully before installing, operating or servicing the fan. Failure to comply with the instructions contained herein 
could result in personal in jury or property damage. We recommend that you keep this booklet for future reference.
This Theia Series bathroom fan uses state-of-the-art technology and is designed with a built-in thermal cut-off for safety and to prolong the life  
of the motor.

PREPARATION

• Tools Required for Assembly (not included): 

Hammer, Drill Bits, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, 
Phillips Screwdriver, Utility Knife

• Helpful Tools (not included): Electric Drill, Wood Screws

• Carefully remove unit from carton.

• Check area above installation location to be sure that wiring can run 

to the planned location and that duct work can be run and the area is 
sufficient for proper ventilation.

 

• Inspect duct work and wiring before proceeding with installation.

• Before installation, provide inspection and future maintenance 

access at a location that will not interfere with installation work.

• You may need the help of a second person to install this fan; one 

person on the attic side and one on the room side.

• Note: Installations may vary depending on how the previous bath fan 

was installed. Supplies necessary for the installation of your bath fan 
are not all included; however, most are available at your local home 
improvement or hardware store.

Summary of Contents for BREVA 110 CFM













Reviews: