background image

 

 

 

1. 

All NAUTICAM Products are warranted against any material and 
manufacturing defects for two years from the date of purchase for 
consumer use. Please fill in the warranty cards shipped with our 
housings and viewfinders at the time of sale and return them to 
your point of purchase within a month. If we do not receive the 
completed warranty card for a particular product, the warranty 
period would be assumed to begin from the day that the product is 
shipped from our facility. This warranty only applies to products 
purchased from authorised NAUTICAM dealers and does not 
extend beyond the original retail purchaser. 

 

 

2. 

To return your product for service, please contact your regional 
authorized service centre(s). Please note that this warranty only 
applies when the product is purchased in the territory where the 
service centre is located. 

 

 

3. 

NAUTICAM accepts no liability for any damage to and defects in 
the housing caused by improper use and/or poor maintenance; it is 
the responsibility of the owner to carefully follow the instructions 
in our manuals. 

 

 

4. 

NAUTICAM does not hold responsibility for damage, of any nature, 
to any equipment used with and/or placed within our products. 

 

 

5. 

NAUTICAM accepts no liability for any loss of captured images or 
the inability to capture images even if it is due to the 
malfunctioning of our products. 

 

 

6. 

Unauthorised modifications and/or repairs of our products will 
automatically invalidate the warranty. 

 

Summary of Contents for NA-EM10II
























Reviews: