background image

 

34 

C

ARE AND 

M

AINTENANCE

 

 

 

Soak the housing system in fresh water after each salt water use, during which all control 
buttons/knobs should be operated a few times to avoid the accumulation of salt residue; 
wipe the housing with a towel before opening. 

 

 

Carefully press the housing lock safety button for a few times to avoid the accumulation 
of salt residue. 

 

 

After each  day of diving, it  is advisable to have the main O-ring in the front  part of the 
housing removed from its groove with the O-ring remover and inspected for damage.  Also 
check that the O-ring retains its original circular shape; never stretch the O-ring excessively 
or remove it with a sharp object.  The O-ring groove should be cleaned to ensure it is free 
from  any  salt  deposit  or  foreign  material;  lightly  coat  the  O-ring  with  the  provided 
lubricant  before  reinstalling  it  in  the  groove.    A  damaged  O-ring  should  be  discarded 
immediately and replaced only with one that is provided by NAUTICAM. 
 

 

Replace  the  main  O-ring  annually.  It  is  recommended  that  you  ship  the  housing  to  our 
distributor for a complete overhaul every year or after every 200 dives. 

Summary of Contents for 17424







































Reviews: