Thumb Screw
Waterhousing
18
19
Washing and Care
• After each use, immerse the seascooter into a container
filled with freshwater for 20 minutes. Then switch on the
seascooter in low speed for 3 seconds, and repeat this
function 5 times to wash away dirt and salt from the
product and motor.
• Dry the seascooter after washing. To dry the seascooter,
remove the battery and leave the battery door opened.
Turn the seascooter in different angles to drain the water.
Use a dry cloth to dry the seascooter. Put the seascooter
in a cool and ventilated area overnight for drying.
• Make sure the seascooter is fully dry before storage.
• To clean the Seascooter do not use detergents; only use
a damp cloth to wipe the unit clean.
• Use a cloth to dry the Seascooter and the battery
compartment.
• DO NOT leave the Seascooter in the water. Always take
the unit out of water when not in use.
Sand or Grit on Seals
Ensure that sand/grit does not get on the seals as correct
maintenance and care is essential. To remove sand or grit
from the seals, rinse the seals in fresh water and apply
fresh lubricant. If there is sand inside the Battery Housing,
gently brush the sand from the unit taking care not to
scratch the sealing surfaces.
Camera Assembly
To attach your camera to Seascooter J-CLASS, you will need a
thumb screw or hardware depending on the mount you are using.
Blocked Propeller
If the Propeller becomes blocked, you can remove the front grille
to remove an obstruction. Below steps must be following to
avoid injury.
(Under normal use the grilles must not be removed.)
1. Remove the SEASCOOTER from the water.
2. Make sure the master switch is in the Off position.
3. Dry the seascooter and remove the battery.
4. Open the grille according to the Fig.21 step 1.
5. Remove obstruction.
6. Reassemble grille (Fig.21 step 2,3).
ATTACHING YOUR CAMERA TO SEASCOOTER MOUNTS
(Can be used with GoPro
®
HERO [3, 3+, 4, 5, 6 or 7] cameras, or
other camera with using the same mount system)
*Camera (and Waterhousing), Attachment Buckle and Thumb Screw are not included
Care & Maintenance
Simply attach the Camera to the mount
and align the hole, Insert And Tighten Up
The Thumb Screw
• Use the specified charger only.
• Must be disposed of properly.
• Do not incinerate, disassemble, damage,
short-circuit or expose to heat.
• The battery contains safety and protection
devices which, if damaged, may cause the
battery to generate heat, rupture or ignite.
• DO NOT THROW WATER ON A BURNING
LI-ION BATTERY. If an exposed battery does
ignite, it will burn even more violently if it
comes into contact with water or even the
moisture in air. A fire extinguisher must be
used.
• Do not expose the battery to water or salt
water, or allow the battery to get wet when
seascooter is not in use.
• Do not subject the battery to strong impacts
or shocks.
• Do not pierce the battery with nails, strike
the battery with a hammer, step on the
battery, or otherwise damage the outer
casing.
• MUST re-charge the battery after EACH USE.
• MUST re-charge the battery at least EVERY
SIX MONTHS when not in use.
• ALWAYS REMOVE the battery from the
Seascooter FOR STORAGE.
• Never leave Lithium-Ion batteries discharged
for long - the batteries do self-discharge and
the charge could drop low enough to
damage the battery.
• Always store the battery partially discharged
in a cool, dry and well-ventilated areas where
it is out of reach of children and away from
ignition sources.
• Do not place the battery in fire, direct
sunlight or other high temperature locations.
Do not apply heat to the battery. Doing so
may cause the battery to generate heat,
rupture, or ignite. Using the battery in this
manner may also result in a loss of
performance and a shortened life
expectancy.
• Always keep the battery terminals clean.
• To prevent short-circuiting or fire, keep the
battery away from other metal objects when
carrying or storing.
• To prevent short-circuiting or fire, always
ensure the charging area is safe during
charging.
Fig.21
1. Remove screws and pull out front grilles
2. Matching cup/cone to reinstall front grilles
3. Front grilles back in places
and fasten screws tight.
