background image

 

 

Page 9

 

 

 

 

Cable Glands 

All cable glands must be properly sealed to prevent water ingress and preserve the IP67 enclosure 
rating.  If a cable gland is not used, a short cylindrical stopper is recommended.  Otherwise, a small 
amount of non-conductive silicone adhesive can be used around the cable at the point where the glands 
tighten down from the outside of the enclosure. 

Antenna Placement 

The included low-profile antennas can be placed under most decks or externally, however, the included 
Iridium antenna cable length is only about 3 feet, whereas the included GPS cable length is 
approximately 10 feet.  The included antenna cabling is more easily susceptible to nearby electrical 
interference, and thus, should be kept away from any power or signal cables.  In addition, nearby large 
extremities should be avoided, including solar panels.  

A good mounting location can include under the bow deck, in T-Top ceiling compartments, and in cabins 
where the antennas can be mounted beneath the deck walkways, but connectivity should always be 
evaluated with 

the Status LEDs

. 

If additional length, external mounting, or better shielding is wanted, the optional high-performance 
low-profile antennas and shielded LMR cables should be used.  While the included low-profile antennas 
are ideal for covert installs, the optional compact high-performance antennas can also be installed 
under the deck/lockers, flush mounted, mast mounted, and more, as shown below. 

 

 

 

 

 

 

 

Summary of Contents for NAVT-01



























Reviews: