10 000 WATT FM BROADCAST TRANSMITTER
FM10
Page 2-4
01 October 2002
2.1.7.3
Protection Reset:
This remote control
circuit must be the equivalent of a single pole,
momentary contact switch. The switch must be in
the 'closed' position when pressed and return to the
'open' position when released. The switch must be
connected such that, when activated, +24V is
connected between the
PROTECTION RESET
(+)
(TB1-5) and
PROTECTION RESET
(-)
(TB1-6)
inputs. The operation of this remote control will
cause the RF power protection circuits to be reset,
allowing the RF output to be restored (if possible),
after a fault has caused the transmitter to be inhibited
indefinitely.
2.1.7.4
Power Increase:
This remote circuit must
be the equivalent of a single pole, momentary contact
switch. The switch must be in the 'closed' position
when pressed and return to the 'open' position when
released. The switch must be connected such that,
when activated, +24V is connected between the
POWER INCREASE
(+)
(TB1-7) and
POWER
INCREASE
(-)
(TB1-8) inputs. The operation of this
remote control will cause the RF output power to be
increased.
2.1.7.5 Power Decrease:
This remote circuit must
be the equivalent of a single pole, momentary contact
switch. The switch must be in the 'closed' position
when pressed and return to the 'open' position when
released. The switch must be connected such that,
when activated, +24V is connected across the
POWER DECREASE
(+)
(TB1-9) and
POWER
DECREASE
(-)
(TB1-10) inputs. The operation of
this remote control will cause the RF output power to
be decreased.
2.1.7.6 Low Power Select:
This remote circuit
must be the equivalent of a single pole single throw
switch. The switch must be connected such that,
when activated, ground potential is applied to
LOW
PWR SELECT
(TB1-18) input. The operation of the
remote control will cause the RF output to be set to
the level adjusted for
low power
operation.
NOTE
A 24V supply is available at TB2-15 of the
control/monitor PWB (A14). The (+) terminal of
each control input may be connected to TB2-15,
which will allow activation of the input by
momentarily connecting the appropriate (-) terminal
to ground.
2.1.8
EXCITER INTERLOCK:
Protection
circuitry within the transmitter will operate the
exciter interlock relay in an attempt to mute the
exciter's RF output when the exciter forward power is
excessive or when the transmitter is turned off. Refer
to exciter service manual and determine the required
contact arrangement, noting that:
-
If a closed contact (normally open) is required
to mute the exciter's RF output, connect the
exciter interlock wires between TB1-13 (
N/O
)
and TB1-15 (
COM
) of the control/monitor
PWB (A14).
-
If an open contact (normally closed) is required
to mute the exciter's RF output, connect the
exciter interlock wires between TB1-14 (
N/C
)
and TB1-15 (
COM
) of the control/monitor
PWB (A14).
2.1.9
RF PERFORMANCE MONITORING:
Forward power, reflected power and a sample of the
RF output are available for external monitoring.
2.1.9.1
Forward Power Level:
A buffered DC
voltage that is representative of the forward power
level is available at the
FWD PWR SAMPLE
terminal (TB2-12) of the control/monitor PWB (14).
This voltage varies according to the square root of
the forward power level and will be 12.6 ± 0.6 volts
DC at 11 000 watts. A ground terminal is provided
at TB2-13 as a sample reference.
2.1.9.2
Reflected Power Level:
A buffered DC
voltage that is representative of the reflected power
level is available at the
REFLD PWR SAMPLE
terminal (TB2-14) of the control/monitor PWB
(A14). This voltage varies according to the square
root of the reflected power level and will be 7.1 ± 0.4
volts DC at 440 watts. A ground terminal is
provided at TB2-13 as a sample reference.
2.1.9.3
RF Output Sample:
A -44 ± 2 dB sample
of the RF output (
RF Monitor
) is available at
RF
MONITOR
BNC coaxial connector J2. This output is
normally applied to a station modulation monitor, but
may be connected to an oscilloscope during
maintenance. The
RF Monitor
output will be a
nominal 4.7 volts RMS, into a 50 ohm load, when the
RF output power level is 11 000 watts.
Summary of Contents for FM10
