background image

6-8

OLYMPIC SMART SCALE 

Model 50/51 Instruction Manual

Repair Procedures

 

Testing the Membrane Switch Panel

Test the membrane switch panel if the

 AVERAGE

/

UNLOCK

KG

/

LB

, or 

ZERO

 

do not function.

Required Items:

„

Allen wrench

„

ESD protection

„

Jumper wires (x2)

„

Voltmeter

To test the membrane switch panel:

1

If the scale is on, press 

ON/OFF

 to turn off the scale, then unplug the 

power cord.

2

Disassemble the scale (see page 6-2).

3

Disconnect the ribbon cable connector from the display PCB (see Figure 6.6).

Figure 6.6

Disconnecting the ribbon cable connector

4

Verify that the membrane switch panel is properly connected.

5

Using two small jumper wires, check the resistance of the malfunctioning 

switch at the corresponding pin on J2 of the display PCB (see Table 6.1). 

6

Using the ground reference point of either pin 5 or 6, check the resistance. 

The resistance should be less than 50

Ω

 (circuit closed) when pressed —

„

If not, replace the membrane switch panel.

Display PCB

Mounting screws (x4)

Ribbon cable connector

NOTE

#

If the 

KG/LB

 disabling switch has been activated (see page 2-1), 

KG/LB

 will be disabled 

and the scale will only display kilograms.

Table 6.1

Control panel button pin out 

Switch

J2 pin on display PCB

Common (ground)

5, 6

Zero

2

Average/Unlock

4

Kg/Lb

3

On/Off

1

Recall

7

Summary of Contents for OLYMPIC SMART SCALE 50

































































Reviews: