Nature's Flame Camino, Manual, Page: 14 / 20

Page 11
16.3.4 Menu Five - Stove State (Fire Status)
In this menu, you can check the correct functioning of
some of the key components of the pellet fi re.
To enter this menu either
1. Press Button (7) (Menu 01 “Set Clock” will appear)
2. Then press and hold (6) for 3 seconds
Or
1. Press (7) CLOCK SETTING MENU will appear
2. Press (1) four times “fi re State” menu, enter using
(7).
This menu is for use by a service technician for
commissioning and diagnostics, and for the customer
when loading pellets into the auger when the fi re has
been completely run out of fuel.
16.3.5 Menu Six - Working Hours
The WORKING HOURS Menu shows the total run hours
done by the fi re.
To enter this menu, proceed as follows:
1. Press Buttons (7) (Menu 01 “Set Clock” will appear).
2. Press button (1) twice until you see (Menu 06
“WORKING HOURS MENU.
3. Press (7) to enter this menu .
4. Press (3) to return to the main screen.
16.3.6 Loading the Screw (Auger)
Insert Models - Loading the Auger should only be
carried out in OFF mode
When the stove is new or the fi re has run out of fuel, the
auger will be empty. In this case it may be necessary to
‘load’ the auger so the fi re will start.
To load the screw/auger, proceed as follows:
1. Press Button (7) (Menu 01 “Set Clock” will appear),
then press and hold (6) for 3 seconds. The display
will show “SCREW STATE”.
2. Use Button (1) to turn the Auger On “SCREW 1” and
button (2) to turn it OFF.
3. Once started auger will run for a couple of minutes
4. Remember to turn the screw OFF (SCREW 0) with
button (2) before exiting, button (3)
5. Empty the burner pot of any pellets before starting
the fi re
Also see “16.3.4 Menu Five - Stove State (Fire Status)”
on page 11.
16.3.7 How to synchronise the remote control with
the fi re
All insert stoves are fi tted with remote-control, radio-
wave handset and a receiver, located on the right-hand
side of the stove. Sometimes, due to interference
from other electrical household appliances (microwave
ovens, satellite decoders, mobile phones) the
connection between the stove and the handset may be
interrupted. If this happens, the following operations
must be carried out to reinstate the connection:
1. Switch the power to the fi re off at the mains switch.
2. Press the triangle keys (1) and (2) on the remote
together for about three seconds. The display will
show “SCEGLI UNITA 0”
3. Using triangle key (2), select the unit frequency to
be loaded (select unit 0 , 1 , 2 , 3 ) Note: 0 or 1
are usually the best but different houses may work
better on other settings.
4. Switch the power to the stove back on (if the unit
is pulled out this will need pushing back into its
cradle) .
5. Press the red button (3).
6. If the operation is successful, UNIT LOADED 0, 1, 2
or 3 will appear on the remote. You may now need
to turn the power to the stove off and back on again
to refresh the connection with the remote.
2000
130°C
SCREW 0
STAT
E 1
Exhaust Fan RPM
Exhaust Temperature
Auger Status
1 = ON 0 = OFF
Stove Status
The auger is activated
2000
150°
COCLEA
1
ST
ATE
The auger is idle
2000
150°
ST
ATE
COCLEA
0