Nature's Comfort NCB-120 Installation And Operation Instructions Manual Download Page 6

Page 

6

 of 

25

 

 

 
F. 20 Year Limited Warranty 

 

Nature's Comfort LLC, of Shipshewana, IN 46565 warrants material and labor on any defects in workmanship on the fire drum for a period of 20 
years from the purchase date to the original owner only (see proration below). If there is a leak in your properly delivered, installed and maintained 
Nature's Comfort boiler, we will repair for the first 5 years at no cost and prorated after that (see below). The water jacket is warranted for a period 
of 10 years from the purchase date to the original owner only (see proration below). Repair can be denied if the unit's water jacket has exceeded 
220 degrees.  
 
This warranty is limited to defective parts and excludes any incidental and consequential damages connected therewith. Nature's Comfort does not 
warranty damage or malfunction to any interior portion of the boiler caused by ash corrosion or allowing the unit to overheat. Ash must be kept 
cleaned out and all interior portions must be completely cleaned out of all ashes and creosote a minimum of 2 times per year, half way through the 
heating season and at the end of heating season. The chimney must be covered when the boiler is not in use. Caulk around chimney and float 
stack must be inspected monthly and re-sealed if necessary. Caulk sealant and rope gaskets are not covered under this warranty. Damage caused 
by abuse, neglect, accidents, improper installation, customer or dealer modification, overheating and/or freezing will not be covered under warranty. 
Damage caused by burning flammable materials (i.e. petroleum products) will not be covered under warranty. Nature's Comfort does not warranty 
boilers against environmental conditions out of its control. Nature's Comfort does not warranty or guarantee against your area's governing laws or 
changes in your area's governing laws that will affect the use or nonuse of the unit. 
 
Nature's Comfort is not responsible for replacement of water, water treatment, antifreeze and glycol, costs of transportation or shipping charges. On 
sight non-warranty parts and labor will be provided at the discretion of your dealer. Please contact your dealer for their current non-warranty rates. 
Labor for repairing or replacing parts under warranty will be covered by your dealer. 
 
Nature's Comfort's wood boilers are not meant to be your sole source of heat. It is the responsibility of the owner to have a backup system in place. 
If you do not have a backup source of heat you are at risk of damage due to lack of heat. Nature's Comfort will not warranty or be responsible for 
any damage caused by lack of heat at your premises or for any cost incurred from using a backup heat system in the event of a boiler failure. 
There is no written or implied performance warranty on the boiler as Nature's Comfort has no control over the installation, structure insulation, 
maintenance, daily operation and heating demand on a unit or what is burned in the boiler. Nature's Comfort will not cover or be held responsible 
for any cost of wood or coal burned in excess of what is expected or considered normal as installation, fuel being used, structure size and insulation 
conditions are out of its control. 

Treatment & Testing 

 

Your boiler must have "Nature's Comfort Boiler Treatment" added during initial filling with water, antifreeze or glycol and must be tested when first 
filled and then annually at the end of a heating season to ensure proper concentration (1,000-1,5000ppm, never below 500ppm minimum or above 
2500ppm max of nitrites) for your warranty to remain valid. The water jacket must remain full of properly treated water at all times after installation 
save for draining, flushing and re-treating. Minimum recommended initial mix ratios for each boiler is: NCB120 & NCB175 - 1.5Qts; NCB250, 
GT220 & GT6000 - 2Qts; NCB325(G) & GT500 - 3Qts, NCB-575 - 6Qts. Contact Nature's Comfort or your dealer to obtain water treatment. You 
must have your water tested for nitrites by your dealer or you may order a more comprehensive test from Wood Boiler Solutions LLC to also satisfy 
warranty requirements. You may order over the phone at (920)324-2007 or you may order online at 

www.woodboilersolutions.com

 using promotion 

code "NCLLC" to receive a 15% discount. Always request results to be sent to you and you must keep them on file to show proof of treatment and 
testing if warranty work is ever needed. Testing done by anyone other than a dealer, Wood Boiler Solutions, a certified lab or Nature's Comfort will 
not be accepted for warranty claims but is encouraged for monitoring treatment levels to obtain the maximum life out of a Nature's Comfort boiler, 
particularly if water is being added throughout a heating season. Nitrite test kits are available from your dealer or Nature's Comfort. Drain, flush, re-
fill and re-treat if water is ever not clear. Visit 

www.naturescomfortllc.com/warranty

 each year for current treatment and testing requirements. 

  

Nature's Comfort On-Site Warranty Proration: 

 

Nature's Comfort will pay costs of warranty work based on the following proration: 
 
Fire Drum: Years 1 - 5: 100%, Year 6 - 90%, Year 7 - 80%, Year 8 - 70%, Year 9 - 60%, Year 10 - 50%, Year 11 - 40%,  
Year's 12 - 14: 30%, Years 15-20: 20% 
 
Water Jacket: Years 1 - 5: 100% Year 6 - 80%, Year 7- 60%, Year 8 - 40%, Year 9 - 20%, Year 10 - 10% 
 

1 Year Warranty on Other Components 

 
Nature's Comfort warranties, to the original owner only, any component a part of the boiler that is defective during normal usage for a period of 1 
year from customer's date of purchase. Shipping for returning defective parts is not included. Replacement/repaired parts are obtained from the 
dealer purchase was made through. After one year, your dealer may charge you for any parts provided or work performed. No warranty parts will 
be provided without first returning the defective part. Replacement/repaired parts carry a 90 day warranty or the fulfillment of the 1 year warranty 
period, whichever comes later. Pump failure due to water quality issues or not bleeding the air out from the bearing before startup are not covered 
under warranty. 

Warranty Procedure 

 

All claims under this warranty must be made through the dealer where the boiler was purchased. If an inspection by the dealer indicates that a 
warranty claim is justified and that all conditions of this warranty have been met, Nature's Comfort will repair or replace the problem part according 
to the above proration. Proof of purchase, treatment and testing and return of the defective part (if applicable) must be provided by the owner of the 
boiler before any warranty is given. All costs of removal, shipment to and from the dealer or Nature's Comfort and losses during shipment and 
reinstallation and any other losses due to the stove being removed shall be covered by the owner of the boiler. If your dealer no longer exists, 
please contact Nature's Comfort via email: 

[email protected]

. It may be necessary for you to obtain quotes from one or more local 

professionals. 
 
This warranty is subject to change without notification. Please visit 

www.naturescomfortllc.com

 for the most up to date warranty and installation 

information.  

 

Nature’s Comfort LLC, 3790 N SR 5, Shipshewana, IN 46565

 

 

Summary of Contents for NCB-120


























Reviews: