background image

 
 

Page 3 

 
Stereoscopic microscopes are used for viewing 3-dimensional objects, inspection or assembly of small 
parts, and for dissection of biological specimen.  They provide an upright, unreversed image which 
permits easy manipulation of the object being viewed while looking through the microscope.  They are 
designed for viewing solid objects at low magnification, but they will also permit viewing of some 
transparent specimen slides. 
 
For optimum viewing satisfaction, follow these simple procedures.  Nomenclature used to describe 
components and controls can be identified by referring to the diagram at left. 
 

UNPACKING 
 

Do not touch any of the lens surfaces while handling the microscope.  Dust, dirt, fingerprints can damage 
the delicate lens surfaces or adversely affect image quality. 
 
Remove microscope stand and head assembly from carton.  Remove rubber eyeshields  and  dustcover.  
Remove “pin spanner wrench” (used to adjust focusing tension), “L hex wrench” (used to remove locking 
set screw on stage plates), and plastic black/white contrast plate (80mm diameter).  Your microscope is 
also supplied with a frosted glass stage plate (80mm diameter), which is already mounted in the 
microscope base. 
 
Examine packing material before you discard it.  Retain the styrofoam container in case you need to 
transport, store, or return the microscope for service.  If it becomes necessary to ship the microscope for 
any reason, pack it in the styrofoam container, and then pack the styrofoam in another corrugated 
shipping container for optimum protection.  Use of the styrofoam alone will not provide adequate 
protection in transit, and will void your warranty. 
 
 

ASSEMBLY & OPERATION

 

 
1.  Install rubber eyepiece shields over top of eyepieces, with the flared portion of the shields positioned 

at the outside edge of eyepieces.  These help block out undesired light reflections, and to position 
your eyes at the proper point above the eyepieces. 

 
2.  Please observe that the head rotates 360 degrees.  To position the binocular head in stand, loosen 

knurled head locking screw.  Rotate head to face either forward or backward, whichever suits your 
preference or needs.  Then, tighten knurled head locking screw. 

 
3.  This model is furnished with  stage plates.  The frosted glass plate is used when viewing transparent 

specimen slides or for viewing some specimen thin enough through which light can pass (insect 
wings, etc.). The black/white contrast plate can be used when viewing opaque objects or for 
dissecting.  Choose side of plate providing best contrast with specimen.  

 

FROSTED GLASS PLATE MUST BE USED IF USING BOTTOM ILLUMINATION.  HEAT 
GENERATED IN BASE FROM BOTTOM LIGHT WILL WARP OR DAMAGE THE PLASTIC 
BLACK/WHITE PLATE.  SUCH DAMAGE WILL NOT BE COVERED BY WARRANTY.  It is 
acceptable to leave the glass plate in place for most viewing purposes. 

 

To switch plates or to reverse sides of contrast plate, use the “L hex wrench” to loosen set screw at 
side of base, only enough to permit removal of plate.  Replace plate and tighten set screw. 

 
4.  Plug cord into a standard 120 volt AC three-wire grounded outlet. 

Summary of Contents for 446TBL








Reviews: