background image

 

2.

To replace bottom light (TBL models only), you will require National part #800-400, same as above.

Remove stage plate and observe lamp held in place by pressure clips in base.  Carefully grasp bulb
and remove from clips by pulling straight out.  Holding new bulb with tissue or cloth to avoid getting
body oil on lamp, push into pressure clips.  Replace stage plate.

3.

Replacement of fuse (TL & TBL models only).

The fuse is located at rear left side of microscope base.  To remove fuse from holder, insert a 6mm
screwdriver blade into slot located in rear of fuse holder cap.  Slightly depress and rotate screwdriver
¼ turn in direction of arrow, release pressure on screwdriver to release the fuse.  Pull cap and fuse
out of fuse holder.  Insert proper fuse into fuse cap.  Insert fuse cap into fuse holder.  Using
screwdriver, rotate fuse cap assembly in opposite direction of arrow until guide slot engages, depress
fuse cap and rotate ¼ turn to lock into holder.

TROUBLESHOOTING 

PROBLEM 

REASON FOR PROBLEM 

SOLUTION 

Light fails to operate. 
    (TL & TBL models only) 

Outlet inoperative. 

Have qualified service technician 
repair outlet. 

AC power cord not connected. 

Plug into outlet. 

Lamp burned out. 

Replace lamp. 

Fuse blown. 

Replace fuse. 

Unable to focus. 

Head of microscope drops from 
its own weight. 

Adjust tension control. 

Poor resolution 
     (image not sharp) 

Objective lenses dirty. 

Clean objective lenses. 

Eyepiece lens dirty. 

Clean eyepiece lenses. 

Spots in field of view. 

Eyepiece lens dirty. 

Clean eyepiece lenses. *** 

***Spots in field of view can also result from dirt on inside of eyepiece.  It is recommended that you have 
service technician clean inside of lens. 

OPTIONAL ACCESSORIES AND PARTS: 

This series is designed to provide optimum optical and mechanical performance at minimum cost. 
Therefore, the design is “complete”.  It does not incorporate provisions for changes or additions (which 
would increase manufacturing cost without increasing the basic good quality performance for which it is 
designed).  The only optional accessory available is WF15x eyepieces, which serve to increase 
magnification by 50%. 

#615-400 

WF15X Eyepieces (pair) 

#800-400 

Replacement bulb, 12v 10w, for all illuminated models 

#801-050 

Replacement fuse, 0.50 amp, for 400TL 120v version 

#801-100 

Replacement fuse, 1.0 amp, for 400TBL 120v version 

#903 

Penlight illuminator (for 400-10-2 non-illuminated model only). Requires 2 each AAA 
batteries (not included). 

#940-410 

Replacement frosted glass stage plate, 80mm dia. (405 Series only) 

#941-410 

Replacement black/white plastic contrast plate, 80mm dia. (405 Series only) 

#941-460B 

Replacement black plastic contrast plate, 80mm dia. (405 Series only) 

#941-460W 

Replacement white plastic contrast plate, 80mm dia. (405 Series only) 

Summary of Contents for 400









Reviews: