National Semiconductor ADC10040 User Manual Download Page 2

Page: 2 / 11

http://www.national.com

Table of Contents

1.0 Introduction

............................................................................................................................................ 3

2.0 Quick Start

............................................................................................................................................. 3

3.0 Functional Description

............................................................................................................................. 3

3.1 The Signal Input

....................................................................................................................... 3

3.2 Digital Data Output.

.................................................................................................................. 3

3.3 ADC10080 Control Pins.

........................................................................................................... 3

3.3.1

The Standby (STBY) Pin

..................................................................................... 3

3.3.2

The Data Format (DF) pin

.................................................................................... 3

3.3.3 The Input Range Select (IRS) Pin

............................................................................... 4

3.3.4 Power Supply Connections

........................................................................................................... 4

4.0 Obtaining Best Results

............................................................................................................................. 4

4.1 Clock Timing

........................................................................................................................... 4

4.2 Coherent Sampling

.................................................................................................................... 4

4.3 FFT Windowing Technique

....................................................................................................... 4

5.0 Hardware Documentation

............................................................................................................... 6

Summary of Contents for ADC10040












Search results

Summary of Contents for ADC10040

Reviews:

Related manuals for ADC10040

Brands by name

Popular brands

National Semiconductor ADC10040, User Manual

Search results

Summary of Contents for ADC10040

Reviews:

Related manuals for ADC10040

Brands by name

Popular brands