manualshive.com logo in svg

National Instruments ZYNQ XC7Z020-1CLG484C, User Manual

Share
Download
National Instruments ZYNQ XC7Z020-1CLG484C User Manual Download Page 48

48

|

ni.com

|

NI Digital System Development Board User Manual

NI ELVIS Analog Breadboard

This breadboard gives access to the analog capabilities of the NI ELVIS development system. 
Analog signals are routed directly from the NI ELVIS edge connector to the breadboard. Pin 
markings on the breadboard match the NI ELVIS signal naming convention. For detailed 
information visit the 

NI ELVIS II Series User Manual

 and 

NI ELVIS II Series Specifications

, 

available at 

ni.com/manuals

.

FPGA Digital IO Breadboard

This breadboard connects digital FPGA I/O signals for custom use in prototyping circuits. When 
configured as outputs these signals are compatible with 3.3 V logic standards, while inputs can 
accept up to 5 V levels. These digital signals also provide protection circuitry from accidental 
connections. For more details see section 

User IO Protection

 

The Digital IO Breadboard gives access to the 3.3 V user supply. This power supply is current 
limited to 0.3 A and it is shared between Pmods, digital breadboard (BB3) and MXP connector 
(J4). See section 

User Power Supplies

 

and 

User Power Supplies Monitoring

 

for a detailed 

description. 

Power Breadboard

he Power Breadboard makes available to the user the power supplies generated by NI ELVIS, 
including the positive and negative programmable supplies, -15 V and +15 V. For detailed 
information visit the 

NI ELVIS II Series User Manual

 and 

NI ELVIS II Series Specifications

, 

available at 

ni.com/manuals

. 

Besides NI ELVIS power supplies, the Power Breadboard gives access to the 5 V power input 
that supplies the entire board. This 5 V rail can come from an external wall supply or the 5 V 
output from NI ELVIS, depending on the use case. For more information on powering options 
see section 

Power Supplies

. 

DSDB Programming Guide

Programming in LabVIEW FPGA

This section demonstrates how to create a LabVIEW project and FPGA VI that performs the 
following:
•

Routes switch SW0 to LED0, which causes LED0 to light when switch SW0 is moved to 
the ON position, and turn off when the switch moved to the OFF position.

•

Routes push button BTN0 to LED2, which causes LED2 to light when button BTN0 is 
pressed, and turn off when the button is depressed.

This example also demonstrates how to compile and run the FPGA VI on the DSDB.

Prerequisites

Hardware

 

Summary of Contents for ZYNQ XC7Z020-1CLG484C
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands