background image

 

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the 

Terms of Use

 section on 

ni.com/legal

 for more information about National Instruments trademarks. Other product and company names mentioned herein are 

trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: 

Help»Patents

 in your software, the 

patents.txt

 file on your CD, or 

ni.com/patents

.

© 2005–2007 National Instruments Corporation. All rights reserved.

374133C

Dec07

Maximum altitude...................................2,000 m

Pollution Degree .....................................2

Safety

This product is designed to meet the requirements of the following 
standards of safety for electrical equipment for measurement, control, 
and laboratory use:

IEC 61010-1, EN 61010-1

UL 61010-1

CAN/CSA-C22.2 No. 61010-1

Note

For UL and other safety certifications, refer to the product label or visit 

ni.com/certification

, search by model number or product line, and click the 

appropriate link in the Certification column.

Electromagnetic Compatibility

Emissions................................................EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity ................................................EN 61326:1997 + A2:2001, 

Table 1

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note

For EMC compliance, operate this device with shielded cabling.

CE Compliance

This product meets the essential requirements of applicable European 
Directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)..............73/23/EEC

Electromagnetic Compatibility
Directive (EMC) .....................................89/336/EEC

Note

Refer to the Declaration of Conformity (DoC) for this product for any 

additional regulatory compliance information. To obtain the DoC for this product, 
visit

ni.com/certification

, search by model number or product line, and click the 

appropriate link in the Certification column.

Summary of Contents for SCXI USB-1357














Reviews: