background image

NI PXIe-1086 Getting Started Guide

|

© National Instruments

|

5

Preparing the Environment

Ensure the environment you are using the NI PXIe-1086 in meets the following specifications.
Ambient temperature range .............................. 0 to 50 °C 

(Tested in accordance with IEC 60068-2-1 and 
IEC 60068-2-2. Meets MIL-PRF-28800F 
Class 3 temperature limits.)

Relative humidity range.................................... 5 to 95%, noncondensing 

(Tested to temperature and humidity levels 
specified in MIL-PRF-28800F)

Maximum altitude............................................. 4600 m (570 mbar) (at 25 °C ambient)

Note

Fan speed selector must be set to 

High

 to meet the maximum altitude 

specification.

Pollution Degree ............................................... 2
For indoor use only.

Note

Refer to the 

NI PXIe-1086 User Manual 

for full specifications.

Installing the PXI Express System

Step 1: Set Up the Chassis

1.

Inspect the chassis interior and exterior for damage. If damage appears to have been caused 
during shipment, file a claim with the carrier.

2.

If you are installing the chassis in an instrument rack, install the rack mount kit for the 
chassis (sold separately). Refer to the instructions supplied with the rack mount kit.

3.

Position the chassis as shown in the following figure, so there is adequate clearance 
between the chassis and surrounding equipment to ensure proper chassis cooling.

Summary of Contents for PXIe-1086

















Reviews: