manualshive.com logo in svg

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108, User Manual, Page: 73 / 83

Share
Download
National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 User Manual Download Page 73

Glossary

©

 National Instruments Corporation

G-3

NI PXI-8108 User Manual

DRAM

Dynamic RAM (Random Access Memory)—Storage that the computer 
must refresh at frequent intervals.

DVI-I

Direct Video Interface, Integrated—A video technology enabling the use of 
both analog and digital video signals.

E

ECP

Extended Capabilities Parallel.

EEPROM

Electronically Erasable Programmable Read Only Memory.

EMC

Electromagnetic Compatibility.

EMI

Electromagnetic interference.

EPP

Enhanced Parallel Port.

expansion ROM

An onboard EEPROM that may contain device-specific initialization and 
system boot functionality.

F

FCC

Federal Communications Commission.

G

g

1.  Grams. 
2. A measure of acceleration equal to 9.8 m/s

2

.

GPIB

General Purpose Interface Bus (IEEE 488).

g

rms

A measure of random vibration—The root mean square of acceleration 
levels in a random vibration test profile.

H

Hz

Hertz—Cycles per second.

Summary of Contents for PXI/CompactPCI Embedded Computer NI PXI-8108




















































































Reviews:

No comments