manualshive.com logo in svg

National Instruments PPC-2115, User Manual, Page: 11 / 48

Share
Download
National Instruments PPC-2115 User Manual Download Page 11

Chapter 2

System Setup

PPC-2115 User Manual

2-2

ni.com

If one of the following situations arises, have service personnel check the 
equipment:

•

The power cord or plug is damaged.

•

Liquid has penetrated into the equipment.

•

The equipment has been exposed to moisture.

•

The equipment does not work well, or you cannot get it to work 
according to the user manual.

•

The equipment has been dropped and damaged.

•

The equipment has obvious signs of breakage.

Do not leave this equipment in an environment where the storage 
temperature may go below –20 °C (–4 °F) or above 60 °C (140 °F). Doing 
so could damage the equipment. The equipment should be in a controlled 
environment.

Caution

There is a danger of explosion if the battery is incorrectly replaced. Replace the 

battery only with the same or equivalent type recommended by the manufacturer. Discard 
used batteries according to the manufacturer’s instructions.

The sound pressure level at the operator’s position according to 
IEC 704-1:1982 is no more than 70 dB (A).

Setup

Follow these steps to set up the PPC-2115:

1.

Unpack the PPC-2115. Be sure your kit includes the following items:

•

The PPC-2115 HMI

•

Eight panel mounting clamps

•

Eight panel mounting screws

•

One 3-pin power connector and wire

•

One PS/2 splitter cable

•

One HMI Resource CD

•

One CompactFlash to IDE adapter card

If any items are missing or damaged, contact National Instruments.

Caution

Be sure system power is off before plugging in or pulling out the CompactFlash 

card.

Summary of Contents for PPC-2115

















































Reviews:

No comments