National Instruments NI PXIe-8133 User Manual Download Page 37 | Manualshive

Page: 37 / 92

background image

Chapter 2

Installation and Configuration

NI PXIe-8133 User Manual

2-20

ni.com

LabVIEW RT Installation

This section explains software installation and switch configuration for
LabVIEW RT on your PXI Express controller.

LabVIEW RT Software Installation

The following section describes the necessary steps to get your
PXI Express embedded controller setup to run LabVIEW Real-Time. In
this section you will configure the boot mode of the controller, verify or
change IP settings, and install LabVIEW Real-Time software.

Complete the following steps to install the LabVIEW RT software.

1.

Boot the NI PXI Express embedded controller into the real-time
operating system. Refer to the

LabVIEW RT Configuration Switches

section or the

LabVIEW RT Menu

section in this manual to configure

the controller for booting into LabVIEW RT.

The PXI Express controller will automatically boot into LabVIEW RT
Safe Mode when no software is installed. LabVIEW RT Safe Mode
loads with the basic real-time operating system and will automatically
attempt to connect to the network using DHCP. If DHCP is not
available, it will then connect to the network with a link-local
IP address.

Tip

You can connect a monitor to the desktop PC to display startup messages such as the

IP address and MAC address.

2.

Open Measurement & Automation Explorer (MAX) on another
computer in the same subnet and expand the

Remote Systems

branch. MAX lists the PXI Express controller as the model name of the
controller followed by the MAC address (for example,

NI-PXIe-8133-2f108562

).

Note

The other computer must have LabVIEW, LabVIEW RT, and any desired drivers

installed.

Tip

Record the PXI Express controller MAC address, located on the side of the controller,

for use in identifying the controller. The label also can be removed and placed on the front
of the controller for easier access.

3.

Click on the appropriate PXI Express controller entry to access the

Network Settings

tab in the right pane view.

4.

(Optional) Enter a name for the RT target in the

Name

text box.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
35
36
37
38
39
...
»

Summary of Contents for NI PXIe-8133





























































































Reviews:

No comments

Related manuals for NI PXIe-8133

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

Brand: Ruckus Wireless Pages: 102

Brand: Barco Pages: 121

Brand: Idis Pages: 31

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: Sony Ericsson Pages: 93

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

Brand: ICP Pages: 142

Modular Fast Fiber Switch Converter MT-RJ

Brand: Lindy Pages: 3

Brand: National Instruments Pages: 45

Brand: Inter-m Pages: 20

Brand: Commax Pages: 122

Brand: NEC Pages: 170

Brand: IEI Technology Pages: 213

55PUS8118 SCSI-2

Brand: IBM Pages: 42

Switch Polarization Print HPP4

Brand: Domburg Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands