National Instruments NI PXIe-8133 User Manual Download Page 24 | Manualshive

Page: 24 / 92

background image

Chapter 2

Installation and Configuration

©

National Instruments

2-7

NI PXIe-8133 User Manual

•

ExpressCard Configuration

—Use this setting to access the

ExpressCard Configuration

submenu. Refer to the

ExpressCard

Configuration Submenu

section for more information.

•

USB Configuration

—Use this setting to access the

USB

Configuration

submenu. Refer to the

USB Configuration Submenu

section for more information.

•

Serial/Parallel Port Configuration

—Use this setting to access

the

Serial/Parallel Port Configuration

submenu. Refer to the

Serial/Parallel Port Configuration Submenu

section for more

information.

PCI Subsystem Settings Submenu

Use this submenu to apply alternate settings to PCI Express devices.

•

64-bit Memory-Mapped IO

—Use this setting to allow some

PCI memory-mapped IO to be above the 32-bit boundary. The default
value is

Disabled

.

•

Maximum Payload

—Use this setting to adjust the maximum payload

size for all PCI Express devices. If set to Auto, the BIOS will choose
an optimal value automatically. The default value is

128 Bytes

.

SATA Configuration Submenu

Use this submenu to apply alternate settings to the hard disk drive (HDD)
interfaces. Normally, you do not need to modify these settings, as the
factory default settings provide the most compatible and optimal
configuration possible.

•

SATA Controller

—This setting specifies whether or not the onboard

SATA controller is enabled or disabled. The default value is

Enabled

.

–

SATA Mode Selection

—This setting determines whether AHCI

mode is enabled or disabled for the SATA port. Some operating
systems, such as Windows 2000, do not support AHCI mode. You
can use this setting to disable AHCI mode and enable IDE mode
so that non-compatible OSes function correctly. The default value
is

AHCI

.

•

Internal Drive (SATA)

—This item displays the onboard SATA drive

detected in the system.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
22
23
24
25
26
...
»

Summary of Contents for NI PXIe-8133





























































































Reviews:

No comments

Related manuals for NI PXIe-8133

Brand: EAW Pages: 6

Brand: EAW Pages: 6

Brand: Salto Pages: 2

Brand: Usr Pages: 2

APS6-400 Series

Brand: Eaton Pages: 114

Low Power Series

Brand: FabiaTech Pages: 77

Brand: Pressalit Care Pages: 31

Wireless Connectivity Cape

Brand: Element14 Pages: 2

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: Axtrinet Pages: 49

Brand: Jäger Pages: 54

Brand: SeaLevel Pages: 19

CORIOview MWP Series

Brand: Tvone Pages: 24

VOYIX 7772-K141

Brand: NCR Pages: 10

i.MX 6SoloLite Linux

Brand: Freescale Semiconductor Pages: 199

Brand: Asus Pages: 56

Brand: Cambium Networks Pages: 32

Brand: ELC Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands