National Instruments NI 9251 Calibration Procedure Download Page 1 | Manualshive

Page: 1 / 8

National Instruments NI 9251 Calibration Procedure Download Page 1

CALIBRATION PROCEDURE

NI 9251 with mini XLR

2 AI, 3 Vrms, 24 Bit, 102.4 kS/s/ch Simultaneous, AC/DC Coupling

This document contains the verification and adjustment procedures for NI 9251 with
mini XLR. For more information about calibration solutions, visit

ni.com/calibration

Contents

Software.................................................................................................................................... 1
Documentation.......................................................................................................................... 1
Test Equipment..........................................................................................................................2
Test Conditions..........................................................................................................................3
Initial Setup............................................................................................................................... 3
Verification................................................................................................................................4

Accuracy Verification....................................................................................................... 4

Adjustment................................................................................................................................ 5

Accuracy Adjustment........................................................................................................5

EEPROM Update......................................................................................................................6
Reverification............................................................................................................................6
Accuracy under Calibration Conditions....................................................................................6
Worldwide Support and Services.............................................................................................. 7

Software

Calibrating the NI 9251 with mini XLR requires the installation of NI-DAQmx 16.1 or later on
the calibration system.

You can download NI-DAQmx from

ni.com/downloads

. NI-DAQmx supports LabVIEW,

LabWindows

™

/CVI

™

, ANSI C, and .NET. When you install NI-DAQmx, you only need to

install support for the application software that you intend to use.

Documentation

Consult the following documents for information about the NI 9251 with mini XLR,
NI-DAQmx, and your application software. All documents are available on

files install with the software.

1
2
3
...
»

Summary of Contents for NI 9251









Reviews:

No comments