National Instruments Network Adapter NI PXIe-1075 User Manual Download

Page: 30 / 78

Chapter 2

Installation and Configuration

NI PXIe-1075 User Manual

2-10

ni.com

Figure 2-5.

Installing PXI, PXI Express, or CompactPCI Peripheral Modules

Power Inhibit Switch LED Indicator

The chassis power inhibit switch has an integrated LED. Refer to
Figure 1-1,

Front View of the NI PXIe-1075 Chassis

, for the location of

both the Power Inhibit switch and the LED. This LED indicates one of four
different conditions:

•

If the inhibit switch LED is steady green (not flashing), the chassis is
powered on and operating normally.

•

If the inhibit switch LED is flashing green, the air-intake temperature
has exceeded the chassis operating range.

•

If the inhibit switch LED is flashing red, the power supply outputs are
not within voltage regulation requirements.

•

If the inhibit switch LED is steady red, the system fans or power supply
fan has failed. The remaining fans will automatically be driven high.

Peripheral Module Front Panel Mounting Screws (2x)

NI PXI Express System Controller

NI PXIe-1075 Chassis

Injector/Ejector Rail

Injector/Ejector Handle

PXI Express Peripheral Module

PXI

e-1075

Summary of Contents for Network Adapter NI PXIe-1075















































































Search results

Summary of Contents for Network Adapter NI PXIe-1075

Reviews:

Related manuals for Network Adapter NI PXIe-1075

Brands by name

Popular brands

National Instruments Network Adapter NI PXIe-1075, User Manual

Search results

Summary of Contents for Network Adapter NI PXIe-1075

Reviews:

Related manuals for Network Adapter NI PXIe-1075

Brands by name

Popular brands