National Instruments MXI-Express x4 Series, Setup Manual, Page: 11 / 17

Share

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Page: 11 / 17

National Instruments MXI-Express x4 Series Setup Manual Download Page 11

Set Up Your MXI-Express x4 System

10

ni.com

Cabling

MXI-Express x4 is available with copper cables of various lengths. Table 4
shows the MXI-Express x4 copper cables

1

available from National

Instruments.

Connect the MXI-Express x4 cable to both MXI-Express x4 cards. The
cables have no polarity, so either end may be connected to either card.

Caution

Do

not

remove the cable after the system is powered on. Doing so can hang

or cause errors in applications communicating with devices behind MXI-Express x4. If a
cable becomes unplugged, plug it back into the system. (You may need to restart your
computer.)

Powering On the MXI-Express x4 System

1.

Power-on all of the expansion chassis in any order you choose.

2.

Power-on the host.

Note

There are no requirements on how MXI-Express x4 expansion chassis are powered

up relative to each other, as long as they are all on before the computer is powered on.

3.

Observe the LED status on the NI PCIe-8371, NI PCIe-8372,
NI PXIe-8370 and NI PXIe-8374 where applicable. A properly
connected and powered up system should report a valid link and power
status on

all

of these boards once the host PC is powered on. Refer to

the

LED Indicators

section for more information.

Typical PCI-PCI bridges and switches are used to add PCI devices to a PCI
hierarchy in which all the bridges and devices are contained within a single
chassis. Because of this, BIOSes and operating systems make the
assumption that all PCI devices in the entire hierarchy will be available as
soon as code execution begins at power-up time. This assumption means
that all of the expansion chassis must be turned on before the host PC for
the BIOS and OS to correctly configure a MXI-Express x4 system.

1

For more information, refer to the

Terminology

section.

Table 4.

National Instruments MXI-Express x4 Copper Cables

Cable Length

(Meters)

Description

Part Number

3 m

MXI-Express x4 copper cable

779725-03

7 m

MXI-Express x4 copper cable

779725-07

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
9
10
11
12
13
...
»

Summary of Contents for MXI-Express x4 Series


















Reviews:

No comments