manualshive.com logo in svg

National Instruments Module SCXI-1503, Calibration Procedure

Share
Download
National Instruments Module SCXI-1503 Calibration Procedure Download Page 1

CALIBRATION PROCEDURE

SCXI -1503

This document contains information for verifying and adjusting the SCXI-1503 module using 
NI-DAQmx 8.1 or later. For more information about calibration, visit 

ni.com/calibration

.

Contents

Software Requirements........................................................................................................................ 1
Documentation Requirements.............................................................................................................. 2
Calibration Interval .............................................................................................................................. 2
Test Equipment .................................................................................................................................... 3
Test Conditions .................................................................................................................................... 3
Calibration Procedures......................................................................................................................... 4

Initial Setup.................................................................................................................................. 5
Self-Calibration............................................................................................................................ 8

MAX .................................................................................................................................... 8

Verification .................................................................................................................................. 8

Verifying the Analog Input.................................................................................................. 8
Verifying the Excitation Current ......................................................................................... 11

Adjustment................................................................................................................................... 11

Adjusting the Analog Input.................................................................................................. 12
Adjusting the Excitation Current ......................................................................................... 14

Where to Go for Support ..................................................................................................................... 15

Software Requirements

Calibrating the SCXI-1503

 

requires installing NI-DAQmx 8.1 or later on the calibration system. 

You can download NI-DAQmx from 

ni.com/downloads

. NI-DAQmx 8.1 or later supports 

self-calibration and external calibration in the LabVIEW, LabWindows/CVI, C/C++, C#, and 
Visual Basic .NET application development environments (ADEs). When you install NI-DAQmx 8.1 or 
later, you only need to install support for the ADE that you intend to use.

™

ni.com/manuals

De

u

tsch

Français

Summary of Contents for Module SCXI-1503
















Reviews:

No comments

Brands by name

Popular brands

Load more brands