manualshive.com logo in svg

National Instruments Module SCXI-1503, Calibration Procedure

Share
Download
National Instruments Module SCXI-1503 Calibration Procedure Download Page 3

©

 National Instruments 

3

SCXI-1503 Calibration Procedure

Test Equipment

National Instruments recommends using the equipment in Table 1 for adjusting and verifying the 
SCXI-1503.

Test Conditions

The following setup and environmental conditions are required to ensure the SCXI-1503

 

meets 

published specifications.

•

Keep connections to the module as short as possible. Long cables and wires act as antennae, which 
can pick up extra noise that affects measurements.

•

Verify that all connections to the calibration system are secure.

•

Maintain an ambient temperature of 25 ±10 °C. The SCXI-1503 module temperature will be 
greater than the ambient temperature. If you plan to operate the SCXI-1503 at a specific 
temperature outside this range, calibrate the module at that temperature.

•

Keep relative humidity below 80%.

Table 1.  

Recommended Equipment

Equipment

Recommended

Model

Parameter

Measured

Minimum Requirements

Calibrator

Fluke 5500A*

Analog Input

If this instrument is 
unavailable, use a 
calibrator that is accurate to 
10 ppm (5 digits).

DMM

PXI-4071

Excitation Current

Analog Input

If this instrument is 
unavailable, use a 
multiranging 7½ digit 
DMM.

SCXI Chassis

SCXI-1000

—

—

DAQ Device

NI PCI(e)/PXI(e) E, M 
or X Series Device

—

16-bit DAQ device 
that is supported by 
NI-DAQmx 8.1 or later.

Terminal Block Connection 
Accessory

SCXI-1306

—

—

Rear Connection Accessory

SCXI-1349

—

—

Terminal Accessory, 50-pin

CB-50

—

—

Ribbon Cable, 50-Pin

NB1

—

—

Cable between SCXI-1349 
and E Series DAQ devices

 SH68-68-EP

—

—

Cable between SCXI-1349 
and M Series or X Series 
DAQ devices

SHC68-68-EPM

—

—

* If using the Fluke 5500A calibrator, you must have the Fluke Fl5xmcal driver installed on the test computer.

Summary of Contents for Module SCXI-1503
















Reviews:

No comments

Brands by name

Popular brands

Load more brands