background image

This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.

What You Need to Get Started

You need the following hardware components to get started with the ISC-178x Smart Camera.

ISC-178x Smart Camera

ISC-178x Smart Camera lens

Starter Kit for ISC-178x Smart Cameras, NI part number 785830-02

X-Code M12 to RJ45 Network Cable, 5 m, NI part number 145230A-05

A-Code M12 to A-Code M12 Power and I/O Cable,
3 m, NI part number 145232A-03

M12 to VGA/USB Splitter Cable, 1 m, NI part number 782022-01

Power and I/O Accessory for ISC-178x Smart Camera, NI part number 145227A-01

Power Supply, PS-10, 100 VAC to 240 VAC, 24 VDC, 5A, NI part number
782698-01

Note

 

Refer to the user manual on 

ni.com/manuals

 for more information about

accessories for the ISC-178x.

Configuring the Hardware

Remove the ISC-178x from the package and inspect the system for damage. Notify National
Instruments if the system appears damaged in any way. Do not use a damaged system.

Ensure that the AC input to the external power supply is disconnected before plugging in or
unplugging any connector. Ground the unit to minimize the possibility of static electricity
damage.

Refer to the following figures while configuring the hardware.

ISC-178x Getting Started Guide

  | 

© National Instruments

  | 

3

Summary of Contents for ISC-178 Series

















Reviews: