background image

Limited Warranty

The GPIB-PRL is warranted against defects in materials and workmanship
for a period of two years from the date of shipment, as evidenced by
receipts or other documentation.  National Instruments will, at its option,
repair or replace equipment that proves to be defective during the warranty
period.  This warranty includes parts and labor.

A Return Material Authorization (RMA) number must be obtained from the
factory and clearly marked on the outside of the package before any
equipment will be accepted for warranty work.  National Instruments will
pay the shipping costs of returning to the owner parts which are covered by
warranty.

National Instruments believes that the information in this manual is
accurate.  The document has been carefully reviewed for technical
accuracy.  In the event that technical or typographical errors exist, National
Instruments reserves the right to make changes to subsequent editions of
this document without prior notice to holders of this edition.  The reader
should consult National Instruments if errors are suspected.  In no event
shall National Instruments be liable for any damages arising out of or
related to this document or the information contained in it.

E

XCEPT AS SPECIFIED HEREIN

, N

ATIONAL 

I

NSTRUMENTS

 

MAKES NO

WARRANTIES

EXPRESS OR IMPLIED

AND SPECIFICALLY DISCLAIMS

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE

.  C

USTOMER

'

S RIGHT TO RECOVER DAMAGES

CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF 

N

ATIONAL

I

NSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE

PAID BY THE CUSTOMER

.  N

ATIONAL 

I

NSTRUMENTS WILL NOT BE

LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA

PROFITS

,

USE OF PRODUCTS

OR INCIDENTAL OR CONSEQUENTIAL DAMAGES

,

EVEN IF ADVISED OF THE POSSIBILITY THEREOF

.  This limitation of the

liability of National Instruments will apply regardless of the form of action,
whether in contract or tort, including negligence.  Any action against
National Instruments must be brought within one year after the cause of
action accrues.  National Instruments shall not be liable for any delay in
performance due to causes beyond its reasonable control.  The warranty
provided herein does not cover damages, defects, malfunctions, or service
failures caused by owner's failure to follow the National Instruments
installation, operation, or maintenance instructions; owner's modification of
the product; owner's abuse, misuse, or negligent acts; and power failure or
surges, fire, flood, accident, actions of third parties, or other events outside
reasonable control.

Summary of Contents for GPIB-PRL









































Reviews: