background image

FP-PWM-520 and cFP-PWM-520

12

ni.com

Specifications

The following specifications are typical for a range of –40 to 70 °C 
unless otherwise noted.

Output Characteristics

Number of channels.......................... 8

Output type ....................................... Sourcing

Output voltage

.................................. Supply voltage

 – (

Output 

current

 

×

 

Output impedance

)

Supply voltage .................................. 5 VDC or 10 to 30 VDC, 

user-provided

Maximum output current per channel

ON resistance

Revision E and later modules

1

... 0.15

Ω

Revision D and earlier 
modules ...................................... 0.3 

Ω

Pulse-width accuracy ........................ –1, +3

μ

s, any period and 

duty cycle

Short-Circuit Protection

Minimum trip current

Revision E and later modules..... 9 A
Revision D and earlier 
modules ...................................... 1 A

Module

Temperature Ranges

–40 to 50 °C

50 to 60 °C

60 to 70 °C

cFP-PWM-520

1 A

0.75 A

0.5 A

FP-PWM-520

1 A

1 A

1 A

1  

The letter in the part number identifies the revision of the module. For example, part 

number 185715A-02 identifies a revision A cFP-PWM-520. The part number is 
printed on a label on the module. On the FP-PWM-520, the label is on the bottom of 
the module. On the cFP-PWM-520, the label is on the back of the module.

Summary of Contents for FIELDPOINT cFP-PWM-520




















Reviews: