background image

Environmental

Refer to the manual for the chassis you are using for more information about meeting these
specifications.

Operating temperature (IEC 60068-2-1,
IEC 60068-2-2)

-20 °C to 55 °C

Storage temperature
(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 85 °C

Ingress protection

IP40

Operating humidity (IEC 60068-2-78)

10% RH to 90% RH, noncondensing

Storage humidity (IEC 60068-2-78)

5% RH to 95% RH, noncondensing

Pollution Degree

2

Maximum altitude

2,000 m

Indoor use only.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.

For additional environmental information, refer to the 

Minimize Our Environmental Impact

web page at 

ni.com/environment

. This page contains the environmental regulations and

directives with which NI complies, as well as other environmental information not included in
this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

 

At the end of the product life cycle, all NI products must be

disposed of according to local laws and regulations. For more information about
how to recycle NI products in your region, visit 

ni.com/environment/weee

.

Battery Replacement and Disposal

Cd/Hg/Pb

Battery Directive

 

This device contains a long-life coin cell battery. If you need to

replace it, use the Return Material Authorization (RMA) process or contact an
authorized National Instruments service representative. For more information about
compliance with the EU Battery Directive 2006/66/EC about Batteries and
Accumulators and Waste Batteries and Accumulators, visit 

ni.com/environment/

batterydirective

.

NI cRIO-9072/9073/9074 User Manual and Specifications

  | 

© National Instruments

  | 

23

Summary of Contents for CompactRIO cRIO-9072



























Reviews: