National Instruments 9775 Calibration Procedure Download Page 1

Page: 1 / 10

CALIBRATION PROCEDURE

NI 9775

±10 V, 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module

This document contains the verification and adjustment procedures for the NI 9775. For more
information on calibration, visit

ni.com/calibration

Software

Calibrating the NI 9775 requires the installation of NI-DAQmx 17.6 or later. You can
download NI-DAQmx from

ni.com/downloads

. NI-DAQmx supports LabVIEW,

LabWindows

™

/CVI

™

, C/C++, C#, and Visual Basic .NET. When you install NI-DAQmx, you

only need to install support for the application software that you intend to use.

Documentation

Consult the following documents for information about the NI 9775, NI-DAQmx, and your
application software. All documents are available on

ni.com/manuals

and help files install with

the software.
•

NI cDAQ-9174/9178 USB Chassis Quick Start

•

NI 9775 Datasheet

•

NI 9775 Getting Started Guide

•

NI-DAQmx Readme

•

LabVIEW Help

•

NI-DAQmx C Reference Help

•

NI-DAQmx .NET Help Support for Visual Studio

Test Equipment

The following table lists the equipment recommended for the performance verification and
adjustment procedures. If the recommended equipment is not available, select a substitute
using the requirements.

Summary of Contents for 9775











Search results

Summary of Contents for 9775

Reviews:

Related manuals for 9775

Brands by name

Popular brands

National Instruments 9775, Calibration Procedure

Search results

Summary of Contents for 9775

Reviews:

Related manuals for 9775

Brands by name

Popular brands